Montgomery Ward 769358, Инструкция по эксплуатации

Страница: 6 / 9

1
•
888
•
557
•
3848 Wards.com
10 11
How to Use (cont.) How to Use
1. To TURN ON OR OFF , press ON/OFF button.
2. To change the
TEMPERATURE SETTING
, press the ARROW KEYS right or left
until the desired setting shows on the display. This temperature will be
maintained between 62–86
°
F.
3. To set the CLEAN AIR FEATURE (only on 10,000 or 12,000 BTU units), press
CLEAN AIR to turn on the ion generator. This will help remove pollen and other
impurities from the air.
4. To adjust the
FAN SPEED
, press the FAN button. Each time the button is
pressed, the fan changes setting (auto, low, medium or high). On dry mode,
the fan is controlled automatically on low.
5. Press the
SLEEP BUTTON to initiate sleep mode. The selected temperature will
increase by 2O
°
F 30 minutes after the mode is selected. The temperature will
then increase by another 2O
°
F after an additional 30 minutes. This new
temperature will be maintained for 6 hours before it returns to the original
program. The sleep mode program can be cancelled at any time during
operation by pressing SLEEP again.
6. As a reminder to check the air filter after 250 hours of operation, the LED will
light up. Press
CHECK FILTER
to reset after cleaning the filter and the light will
go off.
7. Available on cool, dry and auto, press
ENERGY SAVER
and the fan will continue
to run for 3 minutes after the compressor shuts off. The fan then cycles on for 2
minutes at 10 minute intervals until the room temperature is above the set
temperature, at which time the compressor turns on and starts cooling again.
8. Press
MODE
to set auto, cool, dry and fan. The LED beside each will light up
when selected. The unit will automatically initiate the ENERGY SAVER
function under cool, dry and auto (auto-cooling or auto-fan) modes.
A. When you set the mode to AUTO, it will automatically select cooling
or fan-only operation depending on what temperature you have
selected and the room temperature. The fan speed cannot be adjusted.
B. Select
COOL
and a temperature for normal cooling (keep the vent
closed for maximum cooling efficiency).
C. Use
FAN
when cooling is not desired, but you wish to have air
circulation (open the vent during this function). Choose any fan speed
you prefer. The display will show the actual room temperature and the
temperature cannot be adjusted.
D. In
DRY
mode, the air conditioner will operate as a dehumidifier. Since
the conditioned space is a closed or sealed area, some degree of
cooling will continue.
9. When the unit is on or off, press TIMER. The TIMER ON light will illuminate to
indicate the auto start program is initiated.
A. When the time for TIMER ON is displayed, press TIMER again and the
TIMER OFF light illuminates. This indicates the auto stop program is
initiated.
B. Press or hold the arrow buttons to set the auto time by 0.5 hour
increments, up to 10 hours, then at 1 hour increments up to 24 hours.
The display will count down the time remaining until start time.
C. The selected time will register in 5 seconds, and the system will
automatically revert back to display the previous temperature setting or
room temperature when the unit is on. (When the unit is off, there is no
display.)
D. Turning the unit ON or OFF at any time or adjusting the timer setting to
0 will cancel the timed program.
10. If the unit is turned off and on quickly, there will be an
AUTOMATIC 3-MINUTE
TIME DELAYED START
. This prevents overheating of the compressor and
possible circuit breaker tripping. The fan will continue to run during this time.
11. The unit is capable of displaying temperature in
FAHRENHEIT OR CELSIUS.
To
convert from one to the other, press and hold the left and right arrow buttons at
the same time, for 3 seconds.
12. The
FRESH AIR VENT (only on 10,000 or 12,000 BTU units) allows the air
conditioner to:
A. Recirculate inside air.
B. Draw fresh air into the room.
C. Exchange air from the room and draw fresh air into the room.
A. vent closed
B. vent open
C. vent and
exhaust open
13. Push ONE TOUCH (on the remote only) and the unit will automatically shift to
cool operation with auto fan speed and a temperature of 80˚ F. The timer
setting will be cancelled.