© 2011 Monte Carlo Fan Company
5/10/2012
9
1.Check main and branch circuit fuses or circuit break ers.
2.Check line wire connections to fan and switch wire connections in switch housing.
3.Check to make sure the dip switches from the tr ansmitter and receiver are set on the same fre -
quency.
CAUTION: Make sure main power is turned off
4.Make sure forward/reverse switch is firmly in position. F an will not operate when switch is in the
middle.
1.Check to make sure all screws in motor housing are snug (not o ver tightened).
2.Check to make sure the screws which attach the fan blade holder to the motor are tight.
3.Check to make sure wire nut connectors in switch housing are not r attling against each other or
against the interior wall of the switch housing.
CAUTION: Make sure main power is turned off before entering switch housing.
4.Some fan motors are sensitiv e to signals from Solid State v ariable speed controls.
DO NOT USE
a Solid State variable speed control.
5.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear after
this period.
1.Make sure that the ridge of the canop y engages the notch in the downrod ball.
2.Check that all blades are screwed firmly into blade holders.
3.Check that all blade holders are tightened securely to motor .
4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction bo x and
junction box is mounted firmly to ceiling joist.
5.Most fan wobble problems are caused when blade lev els are unequal. Check this lev el by select-
ing a point on the ceiling abo ve the tip of one of the blades. Measure this distance from blade tip
to ceilng. Keeping measure within 1/8", rotate the fan until the next blade is positioned for meas -
urement. Repeat for each blade. If all blade lev els are not equal, y ou can adjust blade lev els by
the following procedure. To adjust a blade tip down, insert a w asher (not supplied) between the
blade and blade holder at the screw closest to the motor . To adjust a blade tip up , insert washer
(not supplied) between the blade and blade holder at the two screws farthest from the motor .
Reverse the position of the w asher if blades mount from top of blade.
6.If blade wobble is still noticeable, interchanging two adjacent (side b y side) blades can redistrib -
ute the weight and possibly result in smoother oper ation.
1.Check wire from fan to mak e sure it is connected to hot wire from house.
2.Check for loose or disconnected wires in fan switch housing.
3.Check for loose or disconnected wires in light kit.
4.Check for faulty light bulbs.
WARNING: Over lamping the fan will result in the fan lights shutting down
until the proper wattage of bulbs are installed.
Reset the lights by turning off the wall switch, breaker,or by remote. Replace bulbs with
the correct wattage bulbs, turn the power on.
CAUTION: Make sure main power is turned off before entering switch housing.
2. If fan sounds noisy:
1. If fan does not start:
3. If fan wobbles:
4. If light does not work:
Trouble Shooting
If you have difficulty operating your new ceiling fan, it ma y be the result of incorrect assembly, installation,
or wiring. In some cases, these installation errors ma y be mistaken for defects. If y ou experience any faults,
please check this Trouble Shooting Chart. If a problem cannot be remedied, or y ou are experiencing difficulty
in installation, please call our Customer Service Center at the number printed on y our parts list insert sheet.
Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service dis-
connecting means to prevent power from being switched on accidentally. When the service dis-
connecting means cannot be locked, securely fasten a prominent warning device, such as a tag,
to the service panel.
Trouble
Suggested Remedy
Содержание 5GIR54XXD-L Series
Страница 10: ......
