background image

6

© 2021 Monte Carlo Fan Collections

7/2021

Battery cover

SET

SET

1

0

1

0

1

0

The remote control buttons control the fan speed as follows:

 Fan speed

1 = minimum speed          2 = low speed      3 = medium low speed     

4 = medium speed         5 = medium high speed       6 = high speed

      

This button turns the fan off.

      

Forward

/

Reverse button: This button is to control direction of fan rotation. Press once

     to change direction of the fan rotation. Fan must be running to reverse.        
     Breeze: 
Press the Breeze button, fan will operates randomly among minimum, low and medium low speed at 

intervals of 30 seconds until the breeze mold is canceled.
Breeze mode can be erased by pressing either the power or speed control buttons.  

Note

: This remote controller has auto resume function. The fan will maintain the last setting when 

turned back on, with the exception of Breeze mode.

Remote Controller Operation

Remove the battery cover from the remote control transmitter and install batteries. 

Replace the cover. This remote uses 2 1.5V/AAA batteries.

Note

: If not using for long periods of time, remove the batteries to prevent damage to 

remote controller, and store the remote controller away from excess heat or humidity. 

The batteries will weaken with age and should be replaced before they leak or corrode as 

this will damage the controller. Dispose of the used batteries properly. Always keep 

batteries out of the reach of children.  

  

Universal Mode and Learning Mode

Your remote controller has two options: “Universal Mode” (mark “0”) and “Learning Mode” 

(mark “1”). 
If choosing “Universal Mode,” simply move the switch to the LOWER position (mark “0”). 

Your fan with the remote controller is ready to use.

Note

: If using Universal Mode, your fan can be controlled with other remote controllers 

with the same setting.
To control the fan with a specific remote controller, choose “Learning Mode” by moving the 

switch to the UPPER position (mark “1”) and then follow the Learn Mode steps below.

Learn Mode
Important

: Turn the power on for ONLY the specific fan you wish to pair with the remote 

controller. Make sure to turn the power off for all other fans with which you use the same 

remote controller.
Restore power to your fan, press and hold the “SET” button to pair the transmitter and 

receiver. You must press the ‘SET” button within 60 seconds of restoring power to the fan.

Note

: Fan will at first operate at minimum speed and light will blink (if your fan has a light) 

after you’ve chosen Learn Mode.

Note

: If the power is already on, you must turn the power off and then back on for the 

remote control setting.

Note

: If you reset the controller to Universal Mode (mark “0”) and later want to pair the 

controller again to a specific fan, you have to repeat the Learn Mode steps.

 

Содержание 3CLNSM60 Series











Отзывы: