background image

4

7

8

9

10

11

12

© 2020 Monte Carlo Fan Collections

1/2020

Place yoke cover and canopy over lead 

wires, safety cable and downrod, and then 

replace the hanger ball.

Replace the hanger ball with pin 

and set screw. Tighten it securely.

 

Warning

: Make sure the 

pin

 is 

installed well on hanger ball with 

downrod. 

Install ball end of downrod into mounting 

bracket opening. Align (engage) slot on 

ball with tab on mounting bracket.

Warning:

 Failure to align slot on ball with 

tab may result in serious injury.

For Canadian installation and for USA fan 

and light kit combinations over 35 lbs, in 

both flush and downrod modes the safety 

cable must be installed into the house 

structure beams using 3” lag screws, 

washers and lock washers provided. 

Make sure that when the safety cable is 

fully extended the lead wires are longer 

than the cable and no stress is placed on 

the lead wires.

Note

: If Installing The Secondary Support 

Safety Cable in the U.S., Do Not Remove 
Knockouts In The Outlet Box.

  

SAFETY CABLE INSTALLATION

Lag screw

Safety cable

Washer

Lock washer

Tab

Slot

Make wiring connections as indicates 

above, using wire connectors provided.    

Connect Black wire from fan to Black 

(Live) wire from house. Connect White 

wire from Fan to White (Neutral) wire from 

house. Connect all green grounded wires 

to Grounded wire from House. Make sure 

that no filaments are outside of the wire 

connectors.

After making the wire connections, the wires 

should be spread apart with the grounded 

conductor and the equipment-grounding 

conductor on one side of the outlet box and 

ungrounded conductor on the other side of 

the outlet box. The splices after being made 

should be turned upward and pushed carefully 

up into the outlet box.              

Lift canopy and fix it on downrod with the 

preinstalled set screw, tighten the screw 

securely. The canopy should adjust for 

any irregularity in the ceiling or outlet 

box.

Power 

supply

Wall switch

Black

Black

White

White

Grounding/Green

Grounded

wires

Ungrounded

wires

Pin

Canopy

Yoke cover

Содержание 3AOR60 Series










Отзывы: