background image

5

© 2018 Monte Carlo Fan Company

05/2018

14

15

17

13

Make wiring connections using wire connectors provided as indicated above.  

Red from fan to Red from remote marked Motor 1.

Purple from fan to Purple from remote marked Motor 2.

Gray from fan to Gray from remote marked Motor 3. 

Blue from fan to Blue from remote marked FOR LIGHT. 

White from fan to White from remote marked FOR LIGHT.

White (Neutral) from house to White from remote marked AC IN N. 

Black (Live) from house to Black from remote marked AC IN L. 

Connect all green grounded wires to Grounded wire from House. 

Make sure that no filaments are outside of the wire connectors.

Insert the remote receiver into mounting bracket.

After making the wire connections, the wires should be spread apart with the grounded 

conductor and the equipment-grounding conductor on one side of the outlet box and 

ungrounded conductor on the other side of the outlet box. The splices after being made should 
be turned upward and pushed carefully up into the outlet box.              

 

  

Lift canopy up, aligning its keyhole slot 

with the preassembled screw on 

mounting bracket and twist 

counterclockwise to lock in place. 

Reinstall the screw removed in step 14 

and tighten all screws securely.

Attach canopy bottom cap onto canopy 

by aligning its notch with the screws on 

mounting bracket and twist clockwise till 

tight. 

  

Loosen 2 and remove 1 preassembled 

screw from the plate on motor. Save 

screw for later use. 

Place light pan over the lead wires and 

attach it onto the plate on motor, aligning 

the keyhole slots on the light pan with the 

preassembled screws on the plate. Twist 

clockwise till lock. 

Partially loosen one and remove one 

preassembled screw from mounting 

bracket. Save screw. 

 

Blue (For Light)
White (For Light)

Red (Motor 1)
Purple (Motor 2)

Gray (Motor 3)

Black (AC IN L)

White (AC IN N)

Green/Ground

Wall Switch

Ground/Green

Black (Live)

White (Neutral)

Power source

Receiver

16

Plate on motor

Light pan

Содержание 3AKR56 D Series











Отзывы: