background image

MST13002 3 

Rev. 10/16/17

ASSEMBLY INSTRUCTIONS

 

     

This is the safety alert symbol used for the SETUP INSTRUCTIONS section of this manual to alert you to potential personal  

 

     

injury hazards. Obey all instructions to avoid possible injury or death. 

IMPORTANT:

 Before attempting to raise any 

 

     

vehicle, check vehicle service manual for recommended lifting surfaces.

SETUP

1.  Remove the 2-piece handle from box. Depress the upper handle lock button and insert the smaller diameter end of the upper  

 

handle into the lower handle end with hole. Make sure the button engages the hole.

2.  Grease the inside of the handle yoke so the handle will rotate freely inside the yoke. Remove the handle yoke screw. Insert the end  

 

of the lower handle all the way in the handle yoke until it engages the release valve assembly. Secure the handle in the handle yoke  

 

by reinstalling the handle yoke screw and tightening the screw. Rotate the handle to see if it is rotating the release valve assembly.  

 

Pull on the handle to make sure it is secured in the handle yoke. If the release valve assembly is not rotating and/or the handle  

 

pulls out of the handle yoke, repeat step 2.

3.

 IMPORTANT:

 In most cases the jack should work normally right out of the box but it is not unusual for air to get trapped in the  

 

jack’s hydraulic system during shipping and handling. There are several symptoms of an air trapped hydraulic system which 

 

include only partial incremental pump stroke, jack will not lift load, jack will not sustain load or pumping feels spongy under load.  

 

The following procedure will purge air from the hydraulic system and only needs to be done if experiencing any of the above 

 

mentioned conditions.

   a)  The saddle should be in its lowest position. Remove the four screws that secure the cover plate to the jack frame so the oil  

 

    filler screw can be removed from the hydraulic power unit reservoir tube.

 

b)  Look inside the oil fill screw hole. You should be able to see the top of the power unit’s cylinder. The hydraulic fluid level should  

 

    be no higher than the top of the cylinder. Correct the fluid level if it is not at the proper height. 

CAUTION: 

In order to prevent  

 

    seal damage and jack failure, never use alcohol, hydraulic brake fluid, or transmission oil in the jack. Use hydraulic jack oil, a  

 

    light turbine oil, Chevron Hydraulic Oil AW ISO 32 or Unocal Unax AW 150.

 

c)  Close the release valve by turning the handle clockwise until it stops. Pump the jack against a load of at least 500 pounds (225  

 

    Kgs). After the load is raised to maximum height, slightly turn the handle in a counterclockwise direction so the load is very  

 

    slowly lowered, while simultaneously and quickly pumping the handle 5 or 6 full incremental pump strokes. After pumping,  

 

    lower the lift arm to its full rest position.

 

d)  Install the oil fill screw. Rotate the handle in a clockwise direction until tight and pump the lift arm to maximum height without a 

 

    load. Repeat steps a) through d) until all the air has been purged from the system. 

 

    Reinstall the cover plate. 

IMPORTANT:

 Before attempting to raise any vehicle, check vehicle service manual for recommended lifting surfaces. 

OPERATING INSTRUCTIONS

 

     

This is the safety alert symbol used for the OPERATING INSTRUCTIONS section of this manual to alert you to potential 

 

     

personal injury hazards. Obey all instructions to avoid possible injury or death.

      

IMPORTANT:

 Before attempting to raise any vehicle, check vehicle service manual for recommended lifting surfaces.

OPERATION

1.  Put vehicle transmission in park or in gear and then apply the emergency brake.
 

To raise load: IMPORTANT:

 Use the vehicle manufacturer's recommended lifting procedures and lifting points before lifting  

 

loads. Turn the handle in a clockwise direction until tight. Position the jack under the load. Proceed to pump the handle in   

 

order to raise the lift arm to the load. As the saddle at the end of the lift arm gets closer to the load, reposition the jack so the  

 

saddle will contact the load firmly and the load is centered on the saddle. Make sure the saddle is correctly positioned. Raise the  

 

load to the desired work height. Place jack stands of appropriate capacity at the vehicle manufacturers's recommended support  

 

areas that provide stable support for the raised vehicle. 

DO NOT CRAWL UNDER VEHICLE WHILE LIFTING VEHICLE OR 

 

PLACING OR REMOVING THE JACK STANDS!

 Once jack stands are positioned, turn the jack handle VERY SLOWLY in a 

 

counterclockwise direction to lower the load to rest on the jack stands. Inspect the relationship between the jack stands and load  

 

to make sure the setup is stable and safe. If the setup is not stable or safe, follow the preceding steps until corrected. 

2. 

To lower load

: Follow the procedures mentioned in  "To raise load" section of the OPERATING INSTRUCTIONS in order to raise  

 

the load off the jack stands. Once the load has cleared the jack stands, remove the jack stands from under the load and away from  

 

the work area. Turn handle very slowly in a counter clockwise direction until the load is completely lowered to the ground. Once the  

 

jack's lifting saddle has cleared the load, remove the jack from under the load. 

DO NOT CRAWL UNDER VEHICLE WHILE 

 

LIFTING VEHICLE OR PLACING OR REMOVING THE JACK STANDS!

 

CAUTION:

 Keep hands and feet away from the  

 

hinge mechanism of the jack. 

Содержание MST13002

















Отзывы: