STEP 1 REMOVE PACKAGING
CAUTION:
Refrigerator is much heavier at the
WRSWKDQDWWKHERWWRP³EHFDUHIXOZKHQPRYLQJ:KHQ
using a hand truck, handle from side only.
PRUDENCE:
Le réfrigérateur est beaucoup
plus lourd en haut qu’en bas. Il faut être prudent lors
des déplacements. Si un diable est utilisé, il faut soulever
le réfrigérateur sur le côté seulement.
• Carefully cut banding at the top and bottom,
remove outer carton.
• Slide out back corner posts (2).
• Slide carton off top of cabinet.
NOTE: IT IS NOT NECESSARY TO LAY CABINET DOWN IN
ORDER TO REMOVE SKID!
• The unit is secured to the skid with 2 full-length
tie-down straps. Remove the ten 5/16
”
bolts from the
base channels in the tie-downs.
CAUTION:
DO NOT
ATTEMPT TO ROLL UNIT OFF
SKID.
PRUDENCE:
IL NE
FAUT PAS ESSAYER DE FAIRE
ROULER LE RÉFRIGÉRATEUR
POUR L’ENLEVER DE LAY
PALETTE.
STEP 2 INSTALL WATER LINE
• A cold water supply is required for automatic icemaker
operation. The water pressure must be between 40 and
120 p.s.i.
• Route 1/4
”
OD copper or GE SmartConnect
™
plastic tubing
between house cold water line and the water connection
location.
• Tubing should be long enough to extend to the front of
the refrigerator. Allow enough tubing to accommodate
bend leading into the water line connection.
NOTE: The only GE-approved plastic tubing is supplied in
the GE SmartConnect
™
Refrigerator Tubing kits. Do not use
any other plastic water supply line because the line is under
pressure at all times. Other types of plastic may crack or
rupture with age and cause water damage to your home.
GE SmartConnect
™
Refrigerator Tubing Kits are available in
the following lengths:
2
’
(.6 m) WX08X10002
6
’
(1.8 m) WX08X10006
15
’
(4.6 m) WX08X10015
25
’
(7.6 m) WX08X10025
Shut off the main water supply.
Turn on the nearest faucet long enough to clear the line of
water.
• Install a shut-off valve between the icemaker water
valve and cold water pipe in a basement or cabinet. The
shut-off valve should be located where it will be easily
accessible.
• Turn on the main water supply and flush debris. Run about
a quart of water through the tubing into a bucket. Shut off
water supply at the shut-off valve.
NOTE: Saddle type shut-off valves are included in
many water supply kits, but are not recommended
for this application.
10
• Remove the four 7/16
”
bolts securing the straps to the skid.
• Support blocks on the bottom of the refrigeration case must
be removed before the refrigerator is taken off the skid or
damage will occur. Carefully, tilt refrigerator and slide blocks
out from beneath.
• Remove toekick. Set aside for final installation.
• Lift the refrigerator off the skid with an appliance dolly.
+DQGOHIURPWKHVLGHV
Installation Instructions
NOTE: Commonwealth of Massachusetts Plumbing Codes
248CMR shall be adhered to. Saddle valves are illegal and
use is not permitted in Massachusetts. Consult with your
licensed plumber.
Remove 2 strap
bolts on each side
Remove 5
base channel
bolts on each
side
STEP 2A WATER LINE INSTALLATION WITH
A REVERSE OSMOSIS SYSTEM
Skip this step when not using an RO System
If the water supply to the refrigerator is from a Reverse
Osmosis Water System, use the refrigerator’s filter bypass
plug. Using the refrigerator’s water filtration cartridge with
the RO filter can result in hollow ice cubes.
Filter Bypass Plug
Floor
Waterline Tubing
Содержание ZICS360NXLH
Страница 19: ...19 Notes...
