Monogram ZDWR240NBS, Руководство по установке

Страница: 5 / 12

31-46122-7
5
Design Guide
THE INSTALLATION SPACE
*For a standard installation of Custom-Framed unit: The
product must be installed so that the front face will project 2"
forward of adjacent cabinets. This position will allow a full door
swing and prevent interference with adjacent cabinetry. The
opening between cabinets must be 23-3/4" minimum.
*For a standard installation of Stainless Steel unit: The product
must be installed so that the front face will project 1-3/4" forward
of adjacent cabinets. This position will allow a full door swing
and prevent interference with adjacent cabinetry. The opening
between cabinets must be 23-3/4" minimum.
)RUDÀXVKLQVWDOODWLRQRI6WDLQOHVV6WHHOXQLW
Install a
ZLGH¿OOHUVWULSRQWKHKLQJHVLGH7KH¿OOHUVWULSZLOODFWDV
a spacer between the door case and adjacent cabinets and will
SUHYHQWLQWHUIHUHQFHZLWKWKHFDELQHWGRRUVZLQJ5HFHVVWKH¿OOHU
strip 2" back from the front face of the unit, or even with
the front edge of the product case (behind the gasket). The width
RIWKHRSHQLQJPXVWEHLQFOXGLQJWKH¿OOHUVWULS
)RUDÀXVKLQVWDOODWLRQRI&XVWRP)UDPHGXQLW
Install a
ZLGH¿OOHUVWULSRQWKHKLQJHVLGH7KH¿OOHUVWULSZLOODFWDV
a spacer between the door case and adjacent cabinets and
will prevent interference with the cabinet door swing. Recess
WKH¿OOHUVWULSEDFNIURPWKHIURQWIDFHRIWKHXQLWRUHYHQZLWK
the front edge of the product case (behind the gasket). The width
RIWKHRSHQLQJPXVWEHLQFOXGLQJWKH¿OOHUVWULS
• The wine chiller, wine reserve and beverage center can
be installed freestanding.
$GGLWLRQDO6SHFL¿FDWLRQV
• A 120 volt 60Hz., 15 or 20 amp power supply is required. An
individual properly grounded branch circuit or circuit break-
er is recommended. Install a properly grounded 3-prong
electrical receptacle recessed into the back wall as shown.
Electrical must be located on rear wall as shown.
NOTE: GFI (ground fault interrupter) is not recommended.
NOTE:
Handle and handle
VWDQGRႇGHSWKLV
(Actual handle may
vary slightly.)
7KHVHSURGXFWVZLOO¿WÀXVKWRDGMDFHQW
cabinets when installed with a Dim. A-width
¿OOHUSDQHORUFOHDW7KH¿OOHUSDQHOVKRXOG
be recessed or set back behind the door
and even with the front edge of the product
case.
Product Dim. A
ZDWI240, ZDBI240 1"
ZDWC240, ZDWR240 1/2"
ZDBC240, ZDBR240 1/2"
In a standard installation, the
product will project forward of
adjacent cabinets. See Dim. A.
Flush
Installation
CABINET
CABINET
CABINET
CABINET
Dim. A
Dim. A
120°
120°
110°
110°
Filler panel or
cleat to be set
back even with
front of case.
Front edge of
product case
Front face
Front face
Front edge of
product case
Standard
Installation
Product Dim. A
ZDWI240, ZDBI240 2"
ZDWC240, ZDWR240 1-3/4"
ZDBC240, ZDBR240 1-3/4"