background image

Title: Bronze BXW-10 Amp Panel Artwork

Date: 5th January 2010

Notes:

1. IMAGE FOR REFERENCE PURPOSES ONLY.

2. VERSION 2

monitoraudio.co.uk

5

10a

11

10

9

8

12

7

6

5

4

3

2

1

amp panel & Controls

1.  Stand-by / On Indicator

The LED indicates whether the unit is in stand-by mode or operational.  It will be illuminated 
red when in stand-by, and green when operational.  The Monitor Audio logo on the front of the  
cabinet will also illuminate depending on operational state.

2.  RCA Line Level Inputs (Left & Right)

When using a stereo amplifier system, connection can be provided by a pair of high-quality 
signal cables from the pre-out section of an amplifier.  Please refer to the crossover table below 
for further advice on which frequency to use.  Experimentation is advised.

Note:

 Cable lengths should not exceed 10 metres to avoid interference from other electrical 

appliances.

3.  LFE Input

This input is to be used when connecting the BXW-10 to an AV amplifier. When using the LFE 
input, the crossover control function does not have an effect. This is due to the crossover 
function  being  controlled  by  the  AV  amplifier  to  which  it  is  connected.  Please  refer  to  the 
crossover  table  below  for  further  advice  on  which  frequency  to  use.    Experimentation  is 
advised.

Note:

 Cable lengths should not exceed 10 metres to avoid interference from other electrical 

appliances.

4.  Volume Control

This control allows the level or volume to be adjusted in order to achieve a balanced overall 
sound. To use this facility you will need to play a selection of familiar music or film excerpts. 
Start with the volume at a low level and increase the level control until a balanced sound is 
established. If using an AV processor or AV receiver amplifier, the system can be adjusted 
by  the  test  tone  function  within  the  set-up  features.  (Refer  to  the  set  up  section  in  the  AV 
processor  or  AV  receiver  amplifier  user  guide.)  When  the  BXW-10  is  correctly  set-up,  you 
should not be able to identify its location easily in the room. 

5.  Crossover Frequency Control

The crossover frequency control only operates when connecting to the BXW-10 using the Line 
Inputs. This control feature is used to set the upper frequency limit (low pass) of the BXW-10. 
The crossover control should be set in accordance with the size or bass output of the main/
satellite  speakers.  Refer  to  the  chart  below  as  a  guide  to  setting  the  crossover  frequency 
control to the optimum position. Much will depend on the correct low frequency response of 
the main speakers and their position in your room. Experimentation is advisable.

Type of Main Speaker

Monitor Audio Product

Crossover 

Control Setting

Large floor-standing speaker

PL200/300; GS20/60; RX6/8; BX6

40-60 Hz

Small floor-standing speaker

BX5; R270

HD

50-70Hz

Large stand-mount/ bookshelf speaker

PL100; GS10; RX2

50-80 Hz

Small stand-mount/ bookshelf speaker

RX1; BX1/2; R225

HD

/250

HD

;R one

HD

60-90 Hz

Small satellite speaker

R45

HD

/90

HD

/180

HD

80-120 Hz

Bronze BXW-10

4

Содержание Bronze BXW-10










Отзывы: