Monessen Hearth DFX DBX24C страница 25 Скачать руководство пользователя | Manualshive

Страница: 25 / 36

background image

33D4047

5

DFX & DBX Series Vent Free Fireplaces

OPERATING INSTRUCTIONS

MILLIVOLT CONTROL LIGHTING INSTRUCTIONS

1.

STOP!

Read the safety information label.

. Make sure the manual shutoff valve is fully open.
3. This gas log set is equipped with an ignition device (piezo) which automatically lights the pilot. If piezo

ignitor does not light the pilot, refer to instructions for

match Lighting instructions, Page 26

.

4. Turn gas control knob clockwise

to the OFF position, set thermostat to lowest setting and turn ON/OFF

switch to OFF position.

5. Wait (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas,

STOP!

Follow

What to Do if You Smell Gas, Page 22

. If you don't smell gas, go to next step.

6. From OFF position, turn the gas control knob counterclockwise

to IGN position. Push in control

knob for 5 seconds.

NOTE: If you are running the heater for the first time, it will be necessary to

press in the control knob for 30 seconds to allow air to bleed out of the gas piping.

7. With the control knob pushed in, push in and release the piezo ignitor button to light the pilot.
8. Continue pushing the control knob in for a further 60 seconds to prevent the flame detector from shut-

ting off the gas while the probe is warming up. Release the control knob.

9. Turn gas control knob counterclockwise

to the ON position.

10. After the pilot has been lit for one minute, the burners can be turned on. Turn the ON/OFF switch to

ON position or adjust thermostat to desired setting.

11. If the gas logs will not operate, follow the instructions

to turn Off Gas to Heater

below and call your

service technician or gas supplier.

TO TURN OFF GAS TO HEATER

1. Turn control knob clockwise

to OFF position to completely shut off the heater.

. If applicable: Turn ON/OFF switch to OFF position and/or set thermostat (if present) to lowest setting.
3. If applicable: Turn off all electric power to the heater.

Figure 33 -
Pilot

FP75

FP2518
control knob

Figure 34 -
Control Knobs

FP518

FP2519
piezo

Figure 35 -
Piezo

FP519

«
...
23
24
25
26
27
...
»

Содержание DFX DBX24C





































Отзывы:

Нет отзывов

Похожие инструкции для DFX DBX24C

Бренд: Parkwood Страницы: 40

Бренд: katell Страницы: 4

Бренд: Valor Fires Страницы: 12

Retrofire RF24XBN

Бренд: Valor Страницы: 32

Бренд: Belleze Страницы: 12

Бренд: Firegear Страницы: 10

e-MatriX 800-500 ST LL

Бренд: Faber Страницы: 24

Бренд: Hearth & Home Страницы: 2

Бренд: Room&Board Страницы: 30

Бренд: UKIAH Страницы: 24

Бренд: Napoleon Страницы: 24

Бренд: abc home living Страницы: 24

BALTIMORE ACC LP

Бренд: Masport Страницы: 20

Бренд: Pelpro Страницы: 40

Бренд: Vermont Castings Страницы: 32

Бренд: baltur Страницы: 60

Бренд: Blumfeldt Страницы: 9

Бренд: Blumfeldt Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды