MOKENEYE SG01Z, Руководство пользователя

Страница: 9 / 14

9
Pickup Tube inlet under the Lid. This helps keep
the Spray Gun parts lubricated and minimizes
clogging.
4. Push the Pickup Tube back into the Canister Lid.
-
If you are spraying at an upward angle or
straight on, position the pickup tube (fig. 5)
toward the back of the canister.
-
If you are spraying at a downward angle,
position the pickup tube (fig. 6) toward the
front of the canister.
This will ensure you spray as much material as
possible before you need to refill.
FILLING THE CANISTER
See Fig. 7
1. Fill the Canister with paint of the correct viscosity,
then carefully screw the Canister back into the
Canister Lid. Securely tighten.
2. Clean any residual liquid from the threads or
sides of the canister and sprayer.
The easiest way to do this without spilling paint is to
leave the full Canister on a flat surface. Lift the Spray
Gun and carefully place the Pickup Tube into the
Canister. When the top of the Canister reaches the
Canister Lid, begin turning the Canister until it
screws into the Canister Lid. Securely tighten.
SPRAYER CONTROLS
SPRAY PATTERN ADJUSTMENT
See Fig. 8, 9, 10
To adjust the spray pattern, loosen the Tip Collar by
turning it counterclockwise (Fig. 8) , then rotate the
Air Cap, then retighten the Tip Collar.
• For a vertical spray pattern, the "ears" of the
Spray Nozzle should be horizontal. Apply up and
down a surface (Fig. 9) .
• For a horizontal pattern, the "ears" should be
vertical. Apply side to side (Fig. 10) .
In other words, the position of the Spray Nozzle and
the spray pattern are at a 90° offset from one
another.
Risk of injury. Never point the
sprayer at any part of the body.
Never pull the trigger while adjusting the spray
setting.
MATERIAL FLOW ADJUSTMENT
See Fig. 11
To control the amount of paint mixture being
sprayed, adjust the Adjusting Knob.
• Turning the Knob clockwise will increase the
amount of paint.
• Turning it counterclockwise will reduce the
amount of paint available.
Do not over-tighten the Knob, as
this will cut off the paint supply, and
may damage the Spray Tip/Needle.
TIP: Always test the spray pattern on scrap
cardboard or similar material first. Begin with the
material adjustment knob on the highest flow setting
(clockwise to the end). If less flow is desired, dial the
material adjustment knob counterclockwise. Heavier,
thicker materials should be sprayed with the knob
dialed farther right. Thinner materials should be
sprayed with the knob dialed farther left.
SPRAY TIP & NEEDLE SELECTION
See Fig. 12
To change the Spray Tip and Needle: The Spray Tip
and Needle must both be the same size.
Check to make sure that they fit together properly
before installation. Typically, a larger Tip/Needle
would be required for thicker material.
1. Make certain that the unit is shut off, remove the
battery pack and clean before proceeding.
2. Loosen and remove the Tip Collar, Air Cap, and
Spray Tip. Be careful not to allow any parts to fall
out of the gun.
3. Loosen and remove the Needle.
4. Assemble the matching Spray Tip & Needle, Air
Cap, and Tip Collar.
5. The sprayer controls will require readjustment
after this procedure is complete.
NOTICE: The Spray Tip can only go in one way. The
notch on the Spray Tip must align with the recess in
the threads of the sprayer.
TIP: Always test the spray pattern on scrap cardboard
or similar material first. Start by selecting the Spray
Tip/Needle with the largest aperture(2.5mm). If
smaller atomized particles is desired, choose a small
kit. Heavier, thicker materials should be sprayed with
a large Spray Tip/needle. Thinner materials should be
sprayed with a small Spray Tip/Needle.
OPERATION
To reduce the risk of fire, personal
injury, and product damage due to
a short circuit, never immerse your tool, battery pack
or charger in fluid or allow a fluid to flow inside them.
Corrosive or conductive fluids, such as seawater,
certain industrial chemicals, and bleach or bleach-
containing products, etc., can cause a short circuit.
If any parts are damaged or
missing, do not operate this
product until the parts are replaced. Use of this
product with damaged or missing parts could result
in serious personal injury.
Do not attempt to modify this tool
or create accessories not
recommended for use with this tool. Any such
alteration or modification is misuse and could result
in a hazardous condition leading to possible serious
injury.
To prevent accidental starting that
could cause serious personal injury,
always remove the battery pack from the tool when
assembling parts, making adjustments, cleaning, or
performing maintenance.
This cordless tool must be used only with the battery
packs and chargers listed below: