7
OPERATING INSTRUCTIONS
To reduce the risk of fire, personal
injury, and product damage due to
a short circuit, never immerse your tool, battery pack
or charger in fluid or allow a fluid to flow inside them.
Corrosive or conductive fluids, such as seawater,
certain industrial chemicals, and bleach or bleach-
containing products, etc. can cause a short circuit.
If any parts are damaged or
missing, do not operate this
product until the parts are replaced. Use of this
product with damaged or missing parts could result
in serious personal injury.
Do not attempt to modify this tool
or
create
accessories
not
recommended for use with this tool. Any such
alteration or modification is misuse and could result
in a hazardous condition leading to possible serious
injury.
To prevent accidental starting that
could cause serious personal injury,
always remove the battery pack from the tool when
assembling parts, making adjustments, or cleaning
the tool.
This cordless tool must be used only with the battery
packs and charger listed below:
MOKENEYE
Battery Pack
2.0Ah
B202005MZ
B202010MZ
3.0Ah
B203005MZ
4.0Ah
B204005MZ
B204010MZ
MOKENEYE
Charger
1A
C10MZ1US
2A
C20M1US
2A
C20MK1US
NOTICE: Please refer to the battery and charger
manuals for detailed operating information.
FUEL GAUGE BATTERY PACKS
Some MOKENEYE battery packs
Models ending
with “Z” include a fuel gauge which consists of
four green LED lights that indicate the level of charge
remaining in the battery pack.
The fuel gauge is an indication of approximate levels
of charge remaining in the battery pack according to
the following indicators:
To actuate the fuel gauge, press and hold the fuel
gauge button. A combination of the four green LED
lights will illuminate designating the level of charge
maintenance charge mode.
-
LED lights up green = When an under-charged
CHARGING THE BATTERY PACK
Battery packs for this tool are shipped in a low
charge condition to prevent possible problems.
Therefore, you should charge it until the green LED
on the front of the charger comes on.
CHARGING A COOL BATTERY PACK
If battery pack is within normal temperature range,
the red LED on charger will come on.
NOTE: If the charger does not charge the battery
pack under normal circumstances, return both the
battery pack and charger to your nearest Mokeneye
Authorized Service Center for electrical check.
-
Charge the battery pack only with the charger
provided.
-
Make sure the power supply is normal household
voltage, 110~240 volts, 50/60 Hz, AC only.
-
Connect the charger to the power supply.
-
For C20M1US/C20MK1US charger, place the
battery pack in the charger aligning raised rib on
the battery pack with the groove in the charger.
-
Press down on the battery pack to be sure contacts
on the battery pack engage properly with contacts
in the charger.
-
Normally the red LED on charger will come on. This
indicates the charger is in fast charging mode.
-
Red LED should remain on for approximately 1 to 2
hours then the green LED will come on. Green LED
on indicates battery pack is fully charged and
charger is in maintenance charge mode.
NOTICE: The green LED will remain on until the
charger is disconnected from the power supply.
-
After normal usage, a minimum of 1 hour of
charging time is required to fully recharge battery
80-100% charged
60-79% charged
40-59% charged
Pack needs to be charged
left. When the level of charge in the battery is below
the usable limit, the fuel gauge will notilluminate
and the battery will need to be recharged.
NOTICE: The fuel gauge is only an indication ofthe
charge left on the battery pack. It does notindicate
tool functionality and is subjectto variation based on
product components, temperature and end-
user application.
For more information regarding fuel gauge battery
packs, please send e-mail to Mokeneye Customer
Service
: [email protected] / Facebook: www
.facebook.com/MokeneyeTools
LED FUNCTIONS OF CHARGER
LED WILL BE ON TO INDICATE STATUS OF CHARGER
AND BATTERY PACK:
Charging with C20M1US/C20MK1US charger
-
LED lights up red = Fast charging mode.
-
LED lights up green = Fully charged and in
battery pack is inserted into charger, indicates hot
battery pack or that battery pack is out of normal
temperature range or deeply discharged or
defective battery pack.
-
No LED on = Defective charger.
