Module-Air
Revised 03-01-2018
General Safety information
SAFETY GUIDELINES- DEFINITIONS
This manual contains information
that important for you to know
and understand. This information
relates to protecting YOUR SAFETY
and PREVENTING EQUIPMENT
PROBLEMS.
GENERAL SAFETY RULES
!WARNING!
This machine was designed for
certain applications only. Tanis
Technologies strongly
recommends that this machine
not be modified and/or used for
any application other than that for
which it was designed. If you have
any questions relative to a
particular application, DO NOT use
the machine until you have first
contacted Tanis Technologies and
confirmed that the product is
suited for your application.
!WARNING!
Failure to follow these rules may
result in serious personal injury.
1. For your safety, read and
understand the instruction
manual before operating the unit.
Learn the un
it’s
application and
limitations as well as the specific
hazards, related to it.
2. Don
’t
use in dangerous
environment.
Don
’t
use this unit in damp or wet
locations or expose to rain.
3. Disconnect unit
before
servicing.
4. Check damaged parts
before
future use of the unit, properly
repair or replace any part that is
damaged.
ADDITIONAL SAFETY RULES FOR
AIR CLEANERS
1. Install Module-Air AF-36xxVT
series air cleaners according to all
electrical and safety codes as well
as the National Electrical Code
(NEC) National Fire Protection
Association (NFPA) and the
Occupational Safety and Health
Act (OSHA). Only someone who is
qualified to do electrical work
should wire the units in.
2. These air cleaners are intended
to be installed at least
8.2 feet (2.5
meters) above the floor.
3. Specific duct design and dust
collector configurations are
required under standards set forth
by the National Fire Protection
Association (NFPA). These are
applicable when collecting
potentially reactive metal dusts
(like aluminum, magnesium and
other materials). NFPA also has
standards that cover other dusts
like grain and plastics, ect. For
guidelines on determining which
precautions should be taken,
please refer to NFPA
497. There may be other
specifications that apply for your
particular application, so please
consult current NFPA standards
that may be acquired at:
NFPA
1 Batterymarch Park
Quincy, MA 02269
1-800-344-3555
This information may contain
safeguards that are required for
the installation, operation and
service of AF-24xx series products.
!
WARNING!
4. Avoid mixing combustible
materials like (but not limited to)
the following: buffing lint,
paper/wood dust, aluminum or
magnesium with dust generated
from the grinding of ferrous
materials. This creates a potential
for fires due to the mixing of
sparks and combustible materials.
5. A machine operator should
NEVER be allowed to put lit
cigarettes or any burning object
into this or any dust control
system.
6. If there is a chance for heated
and/or flammable materials to
enter the unit, installation of the
unit should be evaluated to
determine if a fire
protection/exhaustion systems
should be installed. Federal, State
or local codes, as required by
organizations such as NFPA and
Factory Mutual Insurance or your
insurance carrier may require such
a system.
Module-Air can offer
basic guidelines for such an
installation: however, final
installation design is the
responsibility of the purchaser.
7. Securely anchor unit to a
permanent or fixed supporting
structure, be sure the structure is
rated to hold the weight of the
unit.
8. Support this unit or clamp it to
the work surface when using it in a
portable application to eliminate
potential injury or damage to the
unit
9. Ensure that the intake and
exhaust areas are clear prior to
starting the unit. Clogged intakes
or exhaust can cause explosion
and/or fire.
10. Keep arms and fingers away
from fan. Avoid all exposure to
rotating parts to prevent injury.
11. Do not attempt to
remove/replace filters while unit is
running. Fan blades can cause
severe cuts. Be sure the unit is
disconnected from power source
Содержание AF-36 VT Series
Страница 5: ...Module Air Revised 03 01 2018...
Страница 7: ...Module Air Revised 03 01 2018...
