background image

 

  English   3 

 

 

 

 

 

     

 

 

Before  installing  this  electric  storage  water  heater,  check  and  ensure  that  the 
power  socket  is  reliably  grounded.  Otherwise,  this  water  heater  cannot  be 
installed  and  used  yet.  Do  not  use  the  extension  cord  if  the  power  socket  is 
damaged.  Incorrect  installation  and  use  of  this  water  heater  may  result  in 
serious injuries and loss of property. 
 

Special Caution 
 

 

This  appliance  (water  heater)  is  not  intended  to  be  used  by  persons  with 
special  needs  for  their  physical,  sensory  or  mental  capabilities,  or  lack  of 
experience and knowledge (including children), unless they have been given 
the  supervision  or  instructions  concerning  the  use  of  the  appliance  by  a 
person  who  responsible  for  their  safety.  Children  should  be  supervised  to 
ensure that they are not playing with this water heater. 

 

The  wall  in  which  this  water  heater  is  installed  should  be  able  to  bear  the 
twice bigger load than the weight of this water heater filled fully with water 
without  distortion  and  cracks.  Otherwise,  other  strengthening  measures 
should be adopted. 

 

The  power  socket  must  be  earthed  (grounded)  reliably.  The  installation 
height of the power socket should not be lower than 1.8 m. The rated current 
of the socket should not be lower than 16A.  

 

The  power  socket  and  the  power  plug  should  be  kept  dry  to  prevent 
electrical leakage. If the flexible power cord is damaged, a special power cord 
that is provided by manufacturer must be selected, and replaced by professional 
maintenance personnel. Contact 

MODENA

 Customer Care for help. 

 

For  the  correct  operation  of  the  appliance,  it  is  necessary  to  pay  attention 
that the maximum inlet water pressure is 0.75 MPa, and the minimum inlet 
water pressure is 0.1  MPa 

 

When  using  the  water  heater  for  the  first  time  (or  for  the  first  use  after 
maintenance), the water heater cannot be switched on until it has been filled 
fully  with water. When filling the water, at least  one of the outlet valves of 
the water heater must be opened to exhaust the air. This valve can be closed 
after the water heater has been filled fully with water. 

 

The  pressure  relief  valve  that  attached  with  the  water  heater  must  be 
installed at the cold water inlet of this water heater, and make sure it is not 

PART 1: IMPORTANT SAFETY INFORMATION 

Содержание ES 10IS














Отзывы: