Remove the air hose from the airbrush so that it is easier to work on. Remove
the handle from the body of the airbrush.
Remove the needle locking nut from the airbrush. This should allow you to remove
the needle from the rear of the airbrush assembly. Be careful not to damage the
needle when removing it from the airbrush assembly.
A good quality masking tape or Hobbico
®
Master Mask
™
liquid are both
good masking materials. The job should be evaluated and then decide which
will work best for each situation. Make sure to properly seal the masking tape
down to prevent bleeds. If using Hobbico Master Mask, make sure you follow
the instructions on the container. Using too little of the Master Mask will cause
problems when you try to remove it.
Model Maker warrants this product to be free from defects in material and
workmanship for a period of one (1) year from the date of purchase. During that
time, we will repair or replace, at our option, any product that does not meet these
standards, You will be required to provide proof of purchase date (receipt with UPC
proof-of-purchase or invoice).
If, during the one year warranty period, your Model Maker product shows
defects caused by abuse, misuse, or accident, it will be repaired or replaced, at our
option, at a service charge not greater than 50% of the current retail list price. Be
sure to include your daytime telephone number in case we need to contact you
about your repair.
Under no circumstances will the purchaser be entitled to consequential or
incidental damages.
This warranty gives you specific legal rights, and you may also have other
rights, which vary from state to state.
If you attempt to disassemble or repair this unit yourself, it may void
the warranty.
For service on your Model Maker product, either in or out of warranty, send
it post paid and insured to:
Hobby Services
3002 N. Apollo Drive, Suite 1
Champaign IL 61822 USA
(217) 398-0007
www.hobbyservices.com
This warranty applies to USA and Canada only. For service in other
countries, please inquire at the place of purchase. Customers residing outside the
USA and Canada who wish to have service performed at our USA service center
will be responsible for all postage charges.
This product contains a chemical known to the State of
California to cause cancer and birth defects or other
reproductive harm.
WARRANTY
MASKING
AFTER EACH USE
1
HCAR4201 NEEDLE CAP
2
HCAR4202 NOZZLE CAP
3
HCAR4203 NOZZLE 0.2MM
3
HCAR4204 NOZZLE 0.3MM
4
HCAR4205 SPRAY NOZZLE ASSEMBLY
5
HCAR4206 PISTON O-RING
6
HCAR4207 TEFLON SEAL
7
HCAR4208 BODY
8
HCAR4210 TEFLON SEAL
9
HCAR4211 LOCK SCREW
10 HCAR4212 FIXED NUT
11 HCAR4213 BODY SCREW
12 HCAR4214 NEEDLE CHUCK
13 HCAR4215 NEEDLE SPRING
14 HCAR4216 SPRING STOP
15 HCAR4217 NEEDLE 1.2MM
15 HCAR4218 NEEDLE 1.4MM
16 HCAR4219 NEEDLE STOP SCREW DA450
17 HCAR4221 TAIL CAP DA450
18 HCAR4223 NEEDLE ADJUSTER
19 HCAR4224 PUSH BUTTON
20 HCAR4225 PISTON
21 HCAR4226 BACK LEVER
22 HCAR4227 PISTON O-RING
23 HCAR4228 AIR VALVE O-RING LARGE
24 HCAR4229 AIR VALVE CASING
25 HCAR4230 AIR VALVE O-RING SMALL
26 HCAR4231 AIR VALVE PIN
27 HCAR4232 AIR VALVE SPRING
28 HCAR4233 VALVE PIN GUIDE
29 HCAR4234 AIR TUBE ASSEMBLY
32 HCAR4235 JAR ADAPTER
33 HCAR4236 JAR 22CC
35 HCAR4244 WRENCH
36 HCAR4239 TUBE
PROBLEM: The paint gun does not spray when the trigger is pulled.
SOLUTION:
1. The paint may be too thick.
2. The PSI may be too low.
3. The paint gun may be clogged.
PROBLEM: The paint pulsates.
SOLUTION:
1. The nozzle is loose on the body.
2. The air hole in the top of the jar assembly is plugged.
PROBLEM: The trigger action is rough.
SOLUTION:
1. The needle is bent.
2. The paint gun needs cleaned.
PROBLEM: Paint bubbles in the color cup.
SOLUTION:
The paint gun is clogged.
PROBLEM: The paint sprays out grainy.
SOLUTION:
The paint is too thick. Gradually thin the paint using the proper solution.
PROBLEM: Splattering.
SOLUTION:
This is caused by letting the tip snap back into place. Always release the trigger gently.
TROUBLE SHOOTING
