①
②
③
④
⑤ ⑥
1. LED indicator
2. Multi-functional button (MFB)
3. Micro USB charging jack
4. 3.5mm audio port
5. Secure clip
6. RX / TX switch button
ClipXR is a 2-in-1 Blue tooth stereo audio adapter, which can be easily
switched between receiving and transmitting modes. It is very simple
to access to your audio devices sending or receiving stereo audio via
Blue tooth wirelessly. No extra software installation is needed.
Introduction
-2-
-3-
-1-
Overview
-4-
-5-
-6-
Charge Your Adapter
Highly recommend to charge your adapter100% before usage. It takes
approximately 3 hours to charge the adapter from 0% ~ 100% for the
first time.
1. Using computer: connect the micro USB cable to the
adapter
power
connector and the standard USB port to computers USB port.
2. Using an electrical outlet: connect the micro USB cable to the adapter
and the standard USB port to a DC 5V adapter.
3. Indicator status:
a. RED = charging
b. OFF = charge completed
Note:
1.
When the
battery of the adapter
is nearly exhausted, L
ED
flashes in red
and
a
beep sound
prompts
.
Please charge the adapter.
2. If you have not used the item for a few months, the LED might not
turn red when first charging. It might take 15 - 3 5 m i n u t e s before
the LED turns red. We suggest fully charging the item once at least
in two months.
Please turn the TX/RX switch to RX position before getting ClipXR
started. And TX or RX mode cannot be changed after ClipXR get
started.
Receiver (RX mode), Switch on / off
Receiver
Pairing with a smartphone
1.Ensure the receiver ClipXR is turned off.
2.Keep the receiver ClipXR and your smartphone within 1 meter.
3.Press and hold the MFB button for about 6 seconds until the LED flashes
in red and blue alternatively and fast.em The Blue tooth adapter enters
into pairing mode.
4.Activated the Blue tooth function and search the device from your
smartphone.
5.Select MOCREO ClipXR from the device list, follow the steps and
enter pass code 0000 if requested to pair.
6.Connect the receiver ClipXR to your smartphone.
7.After successful pairing, the LED will flash in blue three times every
2 seconds.
Switch on
: Press and hold the MFB button for about 2 seconds until the
LED flashes blue. Beep sounds will be heard during it.
Switch off
: Press and hold the MFB button for about 3 seconds until
the LED flashed red then go off. Beep sounds will be heard during
it.
Note:
1.Please make sure your smartphone is Blue tooth-enabled before pairing.
2.The pairing mode will last for 2 minutes.
3.Once turned on, the receiver ClipXR will search and connect
automatically with the last paired device which is in working range.
4.The receiver ClipXR will automatically switch off if no device can be
connected within 5 minutes.
5.Clear the pairing list: Turn the Blue tooth receiver ClipXR off, then
press and hold the MFB button for about 12 seconds until the LED
flashes in red for 1 second and then flashes in blue for 1 second.
Afterwards, the receiver enters into pairing mode automatically.
1. Af ter pairing, connect the Blue tooth receiver ClipXR to a 3.5mm
stereo headset or wired speaker via the supplied 3.5mm to 3.5mm audio
cable. Now you can enjoy your favorite music from the medium players
of your smartphone .
2. During music is playing / paused, press the MFB button once to
pause/play.
3. The LED keeps blue when music playing.
4. In standby mode, the LED flashes in blue once every 1 second.
Please turn the TX/RX switch to TX position before getting ClipXR
started. And TX or RX mode cannot be changed after ClipXR get
started.
Switch on
: Press and hold the MFB button for about 2 seconds until the
LED flashes blue.
Switch off
: Press and hold the MFB button for about 2 seconds until the
LED flashes red and goes off.
Transmitter, pairing with a Blue tooth device
The transmitter ClipXR must work together with a Blue tooth headphone /
speaker / receiver.
After connecting the transmitter to a Blue tooth stereo device, you
can enjoy music without wire restriction. Before pairing, please make
sure that your Blue tooth device supports Blue tooth A2DP profile.
Stream music
Pairing procedure
1.Ensure the transmitter ClipXR is turned off.
2.Keep the transmitter ClipXR and your Blue tooth headphone within
1 meter.
3.Press and hold the MFB button for about 4 seconds until the LED
flashes blue quickly. The Blue tooth transmitter enters into pairing
mode.
4.Set your Blue tooth headphone into pairing mode.
5.The transmitter ClipXR will automatically search, pair and connect
with your Blue tooth headphone.
6.After successful pairing, the LED will flashes in blue twice every 2
seconds. Now connecting the transmitter ClipXR to your TV, computer
or music player via the included 3.5mm audio jack to enjoy stereo
music wirelessly.
Note:
1.The pairing mode will last for 2 minutes.
2.Once turned on, the transmitter ClipXR will connect automatically
with the last-paired device.
3.The transmitter will automatically switch off if no devices can be
connected within 10 minutes.
4.LED indicator instruction
In standby mode: flash blue once every 1 second
In pairing mode: flash blue quickly
Connecting mode: flash blue twice every 2 seconds
5.Clear the pairing list: Turn the Blue tooth transmitter ClipXR off,
then press and hold the MFB button for about 12 seconds until the
LED flashes in red for 1 second and then flashes in blue for 1
second. Af ter wards, the transmitter enters into pairing mode
automatically.
The battery used in this device may cause a risk of fire or chemical
bum of mistreated.
To avoid any damage or malfunction of the device, do not drop device
from high positions.
Keep it away from humidity, water and any other liquid. If the device
is exposed to water, moisture and other liquid, do not operate it
to avoid any electrical shock, explosion and damage to the device
or yourself.
Safety information
Transmitter (TX mode), Switch on / off
