MOBOTIX AG
Kaiserstrasse
D-67722 Langmeil
Phone: +49 6302 9816-103
Fax: +49 6302 9816-190
www.mobotix.com
Declaration of Conformity: www.mobotix.com > Support > MxMedia Library > Certificates
MOBOTIX, the MX logo, MxControlCenter, MxEasy, MxPEG and MxActivitySensor are trademarks of
MOBOTIX AG registered in the European Union, the U.S.A., and other countries • Information subject to
change without notice • MOBOTIX does not assume any liability for technical or editorial errors or omissions
contained herein • All rights reserved • © MOBOTIX AG 2017
Technical Specifications V16
Model Variants
Mx-V16A-6* (different combinations of day/night image sensors with the
lens options listed below, as mono or dual cameras)
Lens options
B041 (90 deg. horizontal image angle)
B079 (45 deg. horizontal image angle)
Sensitivity
Color sensor (day): 0.1 lx @ 1/60s; 0.005 lx @ 1s
BW sensor (Night): 0.02 lx @ 1/60s; 0.001 lx @ 1s
Image sensor
1/1.8“ CMOS, 6MP (3072x2048), Progressive Scan
Max. Image Size
6MP (3072x2048)
Image formats
Freely configurable 4:3, 8:3, 16:9 or custom formats (image
cropping), e.g., 2592x1944 (5MP), 2048x1536 (QXGA), 1920x1080
(Full-HD), 1280x960 (MEGA)
Max. frame rate
• MxPEG (max.): 42@HD (1280x720), 34@Full-HD, 24@QXGA,
15@5MP, 12@6MP
• M-JPEG (max.): 26@HD (1280x720), 13@Full-HD, 9@QXGA,
5@5MP, 4@6MP
• H.264 (max.): 25@Full-HD, 20@QXGA
Video Codec
• MxPEG, M-JPEG, JPEG (max. output format 6MP)
• H.264 (max. output size QXGA, bandwidth limitation applicable)
DVR
• In the camera on MicroSD card (SDXC, SDHC pre-installed)
• External, on USB device
• External, on NAS
• Separate live image and full image recording – MxFFS with
archiving function
• Pre- and post-alarm images
• Automatic DVR monitoring with error notification
External
video ring buffer
Directly on NAS or PC/Server, no additional recording software
required
Software (included)
Video management software MxManagementCenter
Image Processing
MxLEO, backlight compensation, automatic white balance, distor-
tion correction
PTZ
Digital pan/tilt/zoom, continuous up to 8X
Alarm/Events
Temperature sensor, shock detector (with firmware version 5.0.1
and higher), additional sensors/IOs via MxMessageSystem, notifica-
tion via e-mail, FTP, IP telephony (VoIP, SIP), visual/sound alarms,
pre- and post-alarm images
Intelligent video anal-
ysis
MxActivitySensor, Video Motion Analysis
Audio
• Microphone/speaker integrated, both 16bit/16kHz (HD wideband
audio)
• Lip-synchronous audio, audio recording
• VoIP/SIP telephony, intercom, remote control using key codes
Interfaces
Ethernet 100Base-T (patch or installation cable), MiniUSB; inputs/
outputs and RS232 via accessories
Security
User/group management, HTTPS/SSL, IP address filter, IEEE 802.1x,
intrusion detection, digital image signature, MxFFS
Certifications
EN 55032:2012, EN 55022:2010, EN 55024:2010, EN 61000-6-1:2007,
EN 61000-6-2:2005, EN 61000-6-3:2007+A1:2011, EN 61000-6-
4:2007+A1:2011, AS/NZS CISPR22:2009+A1:2010, CFR 47, FCC Part
15B
Power Supply
Power over Ethernet IEEE 802.3af
Power Consumption
Typ. 5 W
Protection classes
IP66, IK10+
Operating temperatures –30 to 60 °C/–22 to 140 °F
Dimensions/Weight
Width x height x depth: 261 x 196 x 180 mm; weight: approx.
4,680 g
Standard Delivery
Casing from 3 mm stainless steel (top and front 5 mm stainless
steel), S16 with one or two 6MP sensor modules (day/night)
mounted to front plate, 50 cm/19.7 in patch cable (installed), Allen
wrench 2 mm, screwdriver bit for security screw, multifunctional
tool, module wrench, V16 Quick Install, Drilling Template
Installing the Front Plate
1. Prepare closing the front plate
Prepare this step by inserting the supplied screwdriver bit into the bit
holder and placing the security screw onto the bit. Keep the bit holder
and screw within reach when installing the housing.
2. Insert the front plate
Insert the front plate into the housing upward in the direction of the red
arrows
1
. Push the front plate at the bottom toward the housing
2
and secure the front plate with one hand.
3. Clo se the front plate
Push the security screw upward into the thread and fasten the screw
(torque 1 Nm).
2
1
Initial Operation
Since the V16 contains a modified version of the S16, the initial operation of
the V16 is identical with the initial operation of a S16 (see
S15 Camera Manual,
Chapter 3, «Operating the Camera»).
Since this version of the S16 cannot be operated with hemispheric lenses,
the Hemispheric features and certain display modes (Panorama, Panorama/
Focus, ...) are not available.
Dimensions
261 mm/10.28 in
196
mm/7.72
in
View from front
View from top
261 mm/10.28 in
180
mm/7.09
in
220
mm/8.66
in
Important Notes
Safety Warnings
Notes on Installing:
• This product must not be used in explosion-hazardous
locations.
• Make sure that you install this product as outlined in
Chapter 2, «Installation» of the S15 Camera Manual. A
faulty installation can damage the camera!
• When installing this product, make sure that you are only
using genuine MOBOTIX parts and MOBOTIX connection
cables.
• Only install this product on suitable, solid materials that
provide for a sturdy installation of the fixing elements
used.
Electrical installation: Electrical systems and equipment may
only be installed, modified and maintained by a qualified
electrician or under the direction and supervision of a qualified
electrician in accordance with the applicable guidelines. Make
sure to properly set up all electrical connections.
Electrical surges: MOBOTIX cameras are protected against
the effects of small electrical surges by numerous measures.
These measures, however, cannot prevent the camera from
being damaged when stronger electrical surges occur. Special
care should be taken when installing the camera outside of
buildings to ensure proper protection against
lightning, since
this also protects the building and the whole network infra-
structure.
Never touch the lens: Due to the high performance of the
V16, the area of the image sensor
can get quite hot, especially
when the ambient temperature is also high. This does not
affect the proper functioning of the camera in any way. For
this reason, the product must not be installed within the reach
of persons without the protective lens covers.
Power off before opening the camera: Make sure the power
supply to the camera is disconnected before opening the cam-
era housing (e.g., when exchanging the SD card or connecting
wires inside the housing).
Network security: MOBOTIX products include all of the nec-
essary configuration options for operation in Ethernet net-
works in compliance with data protection laws. The operator
is responsible for the data protection concept across the entire
system. The basic settings required to prevent misuse can be
configured in the software and are password-protected. This
prevents unauthorized parties from accessing these settings.
Legal Notes
Legal aspects of video and sound recording: You must comply
with all data protection regulations for video and sound mon-
itoring when using MOBOTIX products. Depending on national
laws and the installation location of the V16, the recording of
video and sound data may be subject to special documentation
or it may be prohibited. All users of MOBOTIX products are
therefore required to familiarize themselves with all applicable
regulations and to comply with these laws. MOBOTIX AG is not
liable for any illegal use of its products.
Disposal
Electrical and electronic products contain many valuable
materials. For this reason, we recommend that you dispose
of MOBOTIX products at the end of their service life in accor-
dance with all legal requirements and regulations (or deposit
these products at a municipal collection center). MOBOTIX
products must not be disposed of in household waste! If the
product contains a battery, please dispose of the battery sep-
arately (the corresponding product manuals contain specific
directions if the product contains a battery).
Disclaimer
MOBOTIX AG does not assume any responsibility for damages,
which are the result of improper use or failure to comply to the
manuals or the applicable rules and regulations. Our
General
Terms and Conditions apply. You can download the current
version of the General Terms and Conditions from our web-
site at www.mobotix.com by clicking on the
COS link at the
bottom of every page.
§
§
Boot Options of the V16
By default, the camera starts as DHCP client and automatically tries to get
an IP address from a DHCP server. To start the camera in a mode different
from the default mode, you can activate the boot menu of the camera.
1. Prepare the Camera
• Disconnect the camera's power supply.
• Open the housing (see
«Unpacking the V16 and Removing the Front
Plate» on page 2).
• Reconnect the power supply of the camera.
2. Activate the Boot Menu
The red LED lights up 5 to 10 seconds after establishing
the power supply and will stay on for 10 seconds. Press
the "L" key as indicated by the red circle in the figure.
The camera enters the boot menu, ready for selecting
one of the boot options.
The LED now flashes once and repeats the flash signal
after pausing for one second (the number of flashes indicates the current
boot option). To go to the next boot option, briefly press the key again
(< 1 sec). After the last boot option, the camera returns to the first boot
option (LED flashes once).
LED
flashes
Boot
Option
Meaning
Audio
Confirmation*
1 x
Not used
Not available on this camera model.
—
2 x
Factory
Defaults
Starts the camera with factory defaults
(factory default IP address, users and
passwords will not be reset).
Boing
3 x
Automatic IP
Address
Starts the camera as DHCP client and
tries to obtain an IP address from a DHCP
server. If a DHCP server cannot be found or
no IP address can be obtained, the camera
starts with its factory default address.
Boing-Boing
4 x
Recovery
System
Starts the camera with the recovery sys-
tem, e.g., in order to recover from a failed
update of the camera software.
Alarm Sound
*Only on cameras with audio option and installed speaker.
3. Select a Boot Option
Press the key longer (> 2 sec). The camera confirms the selection by flashing
rapidly for 3 seconds. After 20 sec, the camera will play a sound according
to the table above.
If nothing is selected, the camera will resume its normal boot process
after a certain time.
L
Connecting the Cables (Cont.)
3. Connect additional cables (optional)
Connect additional cables (e.g. for ext. speaker/microphone) by pushing
the individual wires into the 8-wire plug (red circle in figure). For additional
information on this topic, see the
S15 Camera Manual in Section 2.2.8,
«External Audio Support».
4. Take care when routing the cables
Make sure that all cables are routed in such a way that they are not dam-
aged between the front plate and the housing when inserting and closing
the front plate. For example, you can use a cable tie (red circle in figure)
to hold the cables together.
All manuals and user guides at all-guides.com
