Security-Vision-Systems
EN
www
.mobotix.com
Innovations – Made in Germany
The German company MOBOTIX AG is known as the leading pioneer in network camera technology and its decentralized concept has made high-resolution video systems
cost efficient.
MOBOTIX AG • D-67722 Langmeil • Phone: +49 6302 9816-103 • Fax: +49 6302 9816-190 • [email protected]
Quick Install
DualMount
Copyright © MOBOTIX AG 2014 • Made in Ger
many • T
echnical infor
mation subject to change without notice.
20 mm
25 mm
30 mm
25 mm
60 mm
Drilling Template
Scale 1:1
Replacing Sensor Modules
All MOBOTIX sensor modules can be used with the DualMount. To replace a sensor module you need the removal tool, which is included
with the delivered parts.
M
O
BO
TIX
M
O
BO
TIX
Additional Mounting Options
Wall mounting of the DualMount
To secure e.g. an entrance area, the DualMount can also be mounted directly above a
door. Before you mount the housing to the wall, make sure that you pry out the drain
louver on the front of the housing (this can be done, e.g., with small pliers).
Surface mounting of the sensor cables
(with ceiling or wall mounting)
The two sensor cables can also be laid openly to the DualMount. For that you need to pry
open two of the four cable openings (see right image) on the backside of the housing.
Recommended mounting steps:
1. Prepare screw holes
(see drilling template on the backside)
When selecting the mounting positions for the DualMount and the camera housing,
ensure that the sensor cables are long enough so that they can be stored easily together
with the hinged ferrites in the DualMount housing. For that we recommend to maintain
a distance of
10 cm
between the opening of the housing and the bend relief of the plug.
2. Lead the sensor cables into the housing and attach the hinged ferrites
Attach one hinged ferrite to each sensor cable. We recommend to maintain a distance
of
2 cm
between the ferrite and the bend relief of the plug.
3. Attach housing
Insert the crossed sensor cables into the mount and place the sealing (item 1.3) on the
housing. Attach the housing to the wall or ceiling and make sure that the sealing is
seated properly.
4. Connect sensor cables, attach and secure sensor modules
Follow the steps 7 to 9 described in section „Installation“.
2 cm
10 cm
Opening
of the
housing
1. Loosen set screws
Loosen the two set screws on the underside of the housing using the provided
1.5 mm Allen wrench.
2. Loosen sensor module
Turn the sensor module with the black module wrench (provided with the
S15D to the left until it reaches the stop (MOBOTIX lettering in the “9-o’clock
position”). Remove the black module wrench.
3. Remove sensor module
Place the removal tool (provided in the package) onto the sensor module.
Remove the module and disconnect it from the sensor cable.
4. Replace sensor module
After disconnecting the sensor module from the sensor cable, proceed as
described in
Installation
(7. Connect sensor cables, 8. Attach sensor modules
and 9. Secure sensor modules).
5. Set dowels or prepare screw holes
Depending on the desired mounting type, you either set the dowels or prepare
screw holes (for the backing plate). In the second case, you can either use
the drilling template provided at the end of this document or use the backing
plate with its five threaded bushings as a drilling template.
6. Mount the housing
Place the
sealing
(item 1.3) on the
SurroundMount housing
(item 1.1). Attach
the housing with or without
dowels
(item 1.7) to the ceiling using the
stainless
steel wood screws
(item 1.6). When using the
backing plate
(behind ceiling
boards or roof linings) use the
stainless steel Allen screws
(item 1.8). You will
need a
crosstip screwdriver
for the wood screws; for the Allen screws you
will need the
3 mm Allen wrench
provided in the package.
7. Connect sensor cables
Connect a sensor cable to each sensor module (one cable through each
opening of the housing). Insert the sensor cable in the socket of the module,
attach the bayonet catch and turn it to the right until it clicks into place.
8. Attach sensor modules
Make sure that the MOBOTIX lettering on the front of the sensor module is
pointing to the “9-o’clock position” as shown in the figure. Turn the sensor
module with the black module wrench (provided with the S15D) to the right
until it reaches the stop.
9. Secure sensor modules
Tighten the two set screws on the underside of the housing to secure each
of the sensor modules. To do this, use the provided 1.5 mm Allen wrench.
Warning: Do not overtighten the screws (plastic housing!).
