background image

 

When attaching the handle, you had better squat just behind the pallet truck. Then you: 

 
2.1

 Insert the draw-bar onto the pump piston (303)

then use a hammer to insert the axle with hole 

(105A)

 into the hydraulic pump. (See fig. 2 ). 

 
 
 
                                                                   

2.2

 

Let control handle(117 or 120G) to the ‘

LOWER

’ position, then 

pass  the  adjusting  nut(104),  adjusting  bolt(103)  and  chain(102) 
through the hole of axle(

105A

) with your hand (See fig. 3). 

 

Fig. 2 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Fig. 3 

2.3

 Press the draw-bar (110, 110B or 111G) down, take away the pin(#2) (See Fig. 1). 

 

2.4

 

Let the control handle (117 or 120G) on ‘

RAISE

’ position, then raise the lever plate (319) with 

the  pin  (#2)  and    insert  the  adjusting  bolt(103)  into  the  front  slot  of  lever  plate  (319),  note  to 
keep the adjusting nut (104) on the under side of the lever plate. 

 

2.5

 Use a hammer to tap another elastic pin (106) into the axle with hole (

105A

). 

The draw-bar is now assembled to the pump. 
 

3.    TO ADJUST RELEASE DEVICE 

 
On  the  draw-bar  of  this  pallet  truck,  you  can  find  the  control  handle(117  or  120G)  which  can  be 
regulated in three positions : 

Raise

             

   

  -handle down 

Drive

 position 

   

-handle in center position 

Lower

                  -handle up, the lever moves back the drive position when released.   

                       

If however they have been changed, you can adjust according to following step: 

3.1

  If  the  forks  elevate  while  pumping  in  the 

DRIVE 

position,  turn  the  adjusting  nut  (104)  on  the 

adjusting bolt(103) or screw(318) clockwise until pumping action does not raise the forks and the 

Содержание ECO I-55
















Отзывы: