WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.
To clear a fault indication, switch off the power to the luminaire and then hold the test button for 10 seconds.
SELF-TEST FUNCTION
When first connected to the mains supply, the fitting will carry out an initial 3-second function test. Any faults will
be indicated by the bi-colour LED indicator.
This product is programmed to carry out its own self-test operation according to the following programme:
Every 30 days
10-second function test
Every 180 days
3-hour duration test
The test button on the side of the fitting can also be used to initiate functional testing as required – the luminaire
will go into emergency mode while the test button is held in.
Following self-tests, the unit will revert to charging mode, and any faults will be indicated by the bi-colour LED
indicator as follows:
LED indicator
Status
Slow flash green (3 sec on, 1 sec off)
Charging
Solid green
Fully charged
Fast flash green (0.1 sec on, 0.1 sec off)
Function test underway
Slow flash green (1 sec on, 1 sec off)
Duration test underway
Solid red
Lamp fault (open circuit / short circuit)
Slow flash red (1 sec on, 1 sec off)
Battery fault or failed duration test
Indicator off
Emergency mode
To clear a fault indication, switch off the power to the luminaire and then hold the test button for 10 seconds.
WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.
GENERAL
This product contains a light source of energy efficiency class D to Regulation (EU) No. 2019/2015 and (UK)
2021 No. 1095.
This product contains a non-replaceable LED light source and a control gear which can be replaced by a
professional.
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the
product.
Installing in areas where the temperature consistently drops below 0°C may shorten the battery life.
This product contains a light source of energy efficiency class D to Regulation (EU) No. 2019/2015 and (UK)
2021 No. 1095.
This product contains a non-replaceable LED light source and a control gear which can be replaced by a
professional.
GENERAL
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the
product.
Installing in areas where the temperature consistently drops below 0°C may shorten the battery life.
This product is DALI compatible. Relevant DALI software and control gear is required for use of this
functionality.
This product should be dismantled for disposal when it reaches the end of its life. Please see website for
dismantling instructions.
This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities
for where facilities exist.
The batteries in this luminaire are Lithium Ion and must be disposed of correctly. Please contact the local
authorities for the disposal of this toxic waste.
WARRANTY
This product has a warranty of 5 years (excluding battery) from date of purchase. Failure to install this product
in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the
batch code will invalidate the warranty. If this product should fail within its warranty period, it should be returned
to the place of purchase for a free of charge replacement. ML Accessories does not accept responsibility for
any installation costs associated with the replacement product. Your statutory rights are not affected. ML
Accessories reserve the right to alter product specification without prior notice.
TEST RECORD
Recommended routine test procedure in accordance with BS5266:
•
Daily check – check status of bi-colour LED indicator
•
Monthly functional test – the luminaire will perform this function without any action from the user.
Alternatively, simulate a mains supply failure for approx. 30 seconds by operation of key switch, switching
off circuit breaker or using test button. Ensure normal supply is restored after test and check status of bi-
colour LED indicator
•
3-hour duration test – the luminaire will perform this function without any action from the user. Alternatively,
simulate a mains supply failure for 3-hour continuous test by operation of key switch, or switching off circuit
breaker. Ensure normal supply is restored after test and check status of bi-colour LED indicator
•
If the luminaire fails any of the above tests, please contact a qualified electrician. Results should be
recorded, even when obtained via the self-test function. See below for test record sheet
