MKS Baratron 223B Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 31

MKS Baratron 223B Скачать руководство пользователя страница 11

Chapter One: General Information

Introduction

3

Chapter One: General Information

Introduction

The Type 223B Pressure Transducer measures differential pressure according to its full scale
range and provides a 0 to ±1 Volt signal which is linear with pressure. Optionally the output can
be 0 to ±5 Volt. Standard full scale ranges are 0.5, 5, 50, 500 in. H

2

O; 1, 10, 100, 1000 Torr; or

1, 10, 100, 1000 cm H

2

O.

The Type 223 can be powered from ±15 or ±12 Volt supplies, and is composed of an Inconel

®

sensor, printed circuit board, and cover.

The sensor is made of three parts:

1. A taut metal diaphragm supported by thick-walled Inconel rings,

2. A dimensionally stable ceramic electrode which senses the diaphragm’s deflection,

3. A reference cover through which a glass-to-metal feedthrough terminal passes an

electronic signal to the printed circuit board.

A terminal block allows connection to the power supply and signal readout.

«
...
9
10
11
12
13
...
»

Содержание Baratron 223B
































Отзывы:

Нет отзывов