manualshive.com logo in svg

MK Diamond Products HD-101R, Инструкция по эксплуатации и список запасных частей

Поделиться
Скачать
MK Diamond Products HD-101R Скачать руководство пользователя страница 24

24

(A)

Position Movable Cutting Table 

to the front of the saw and 

raise the Blade Guard.  

Tighten wing-nut

(B)

Locate the Shaft Lock push  

button on the underside of  

the Cutting Head

(C)

Depress and hold the Shaft 

Lock pushbutton and remove 

Retaining Nut and Outer 

Flange using the Blade Wrench

noTe:    The Adjustable Cutting Guide can be used on either side of the Diamond Blade.  

(A) 

Loosen Adjustable Cutting 

Guide retaining thumbscrew 

and place it over the Movable 

Cutting Table Ruler/Stop  

(B) 

Place the Adjustable Cutting 

Guide onto the Movable Cutting 

Table Ruler/Stop and tighten  

the retaining thumbscrew  

(D)

Raise Cutting Head and Install 

Diamond Blade 

onto Blade Shaft

(E)

Verify the Blade is seated on 

the Blade Shaft and direction 

of rotation is correct

(F)

Install Retaining Nut and Outer

Flange, depress and hold the

Shaft Lock pushbutton 

and tighten

HD-101r aSSemBlY

DiamonD BlaDe inSTallaTion

aDJUSTaBle CUTTinG GUiDe inSTallaTion

noTe:    When installing the Retaining Nut, do not “cross-thread” and DO NOT over tighten.

Содержание HD-101R

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды