background image

 

A-6

 

 

About Manual 

 

The following manual is also related to this product. 
In necessary, order it by quoting the details in the table below. 
 

Related Manual 

 

Manual name 

Manual No. 

(Model code) 

Web Server Module User's manual 

SH-080320E 

(13JR58) 

 
 
 
 
Compliance with the EMC and Low Voltage Directives 

(1) For programmable controller system 

To configure a system meeting the requirements of the EMC and Low 
Voltage Directives when incorporating the Mitsubishi programmable 
controller (EMC and Low Voltage Directives compliant) into other 
machinery or equipment, refer to Chapter 9 "EMC AND LOW VOLTAGE 
DIRECTIVES" of the QCPU User's Manual (Hardware Design, 
Maintenance and Inspection). 
The CE mark, indicating compliance with the EMC and Low Voltage 
Directives, is printed on the rating plate of the programmable controller. 

 

(2) For the product 

For the compliance of this product with the EMC and Low Voltage 
Directives, refer to Section 9.1.3 "Cables" in Chapter 9 "EMC AND LOW 
VOLTAGE DIRECTIVES" of the QCPU User's Manual (Hardware Design, 
Maintenance and Inspection). 

 
 

Содержание QJ71WS96 Series





















Отзывы: