S1
S2
S3
S1
S2
S3
6
6. Electrical work
6.2. Field electrical wiring
Outdoor unit model
50V
85V
140V
112Y, 140Y
Outdoor unit power supply
~/N (single), 50 Hz, 230 V ~/N (single), 50 Hz, 230 V ~/N (single), 50 Hz, 230 V 3N~ (3 phase), 50 Hz, 400 V
Outdoor unit Circuit Breaker capacity
*1
16 A
25 A
40 A
16 A
Wiring
Wire No. ×
size (mm²)
Outdoor unit power supply, earth
3 × Min. 1.5
3 × Min. 4
3 × Min. 6
5 × Min. 1.5
Interface unit/Flow temp. controller-Outdoor unit
*2
3 × 1.5 (polar)
3 × 1.5 (polar)
3 × 1.5 (polar)
3 × 1.5 (polar)
Interface unit/Flow temp. controller-Outdoor unit earth
*2
1 × Min. 1.5
1 × Min. 1.5
1 × Min. 1.5
1 × Min. 1.5
Remote controller-Interface unit/Flow temp. controller
2 × 0.3 (Non-polar)
2 × 0.3 (Non-polar)
2 × 0.3 (Non-polar)
2 × 0.3 (Non-polar)
Circuit rating
Outdoor unit L-N (single)
Outdoor unit L1-N, L2-N, L3-N (3 phase)
*3
AC 230 V
AC 230 V
AC 230 V
AC 230 V
Interface unit/Flow temp. controller-Outdoor unit S1-S2 *3
AC 230 V
AC 230 V
AC 230 V
AC 230 V
Interface unit/Flow temp. controller-Outdoor unit S2-S3 *3
DC 24 V
DC 24 V
DC 24 V
DC 24 V
Remote controller-Interface unit/Flow temp. controller
*3
DC 12 V
DC 12 V
DC 12 V
DC 12 V
*1. A breaker with at least 3.0 mm contact separation in each poles shall be provided. Use earth leakage breaker (NV).
*2. Max. 80 m
*3. The
fi
gures are NOT always against the ground.
S3 terminal has DC 24 V against S2 terminal. However between S3 and S1, these terminals are NOT electrically insulated by the transformer or other device.
Notes: 1. Wiring size must comply with the applicable local and national codes.
2. Power supply cables and the cables between Interface unit/Flow temp. controller and outdoor unit shall not be lighter than polychloroprene sheathed
fl
exible cables. (Design 60245 IEC 57)
3. Be sure to connect the cables between Interface unit/Flow temp. controller and outdoor unit directly to the units (no intermediate connections are al-
lowed).
Intermediate connections may result in communication errors. If water enters at the intermediate connection point, it may cause insuf
fi
cient insula-
tion to ground or a poor electrical contact .
(If an intermediate connection is necessary, be sure to take measures to prevent water from entering the cables.)
4. Install an earth longer than other cables.
5. Do not construct a system with a power supply that is turned ON and OFF frequently.
Warning:
In case of A-control wiring, there is high voltage potential on the S3 terminal caused by electrical circuit design that has no electrical insulation between power
line and communication signal line. Therefore, please turn off the main power supply when servicing. And do not touch the S1, S2, S3 terminals when the power
is energized. If isolator should be used between indoor unit and outdoor unit, please use 3-pole type.
Outdoor Unit
3 poles isolator
Power
supply
Isolator
Interface unit /
Flow temp.
controller
01̲ BH79D067L02̲EN.indd 6
01̲ BH79D067L02̲EN.indd 6
2009/06/03 9:51:03
2009/06/03 9:51:03
Содержание PUHZ-HW*HA series
Страница 8: ......
