Mitsubishi MELSEC iQ-R series Скачать руководство пользователя страница 53

Страница: 53 / 86

7 OPERATION EXAMPLES

7.1 Programming Procedure

OPERATION EXAMPLES

This chapter describes the programming procedure and basic program of the temperature control module.

7.1

Programming Procedure

Create a program that operates the temperature control module using the following procedure.

Set parameters.

Create a program.

Using function blocks (FBs) can reduce the load at programming and improve the readability of a program.
For details on the function blocks, refer to the following.



MELSEC iQ-R Temperature Control Module Function Block Reference

7.2

Program Examples

Standard control

System configuration

The following shows a system configuration example.

(1) Power supply module (R61P)
(2) CPU module (R120CPU)
(3) Temperature control module (R60TCTRT2TT2)
(4) Input module (RX10)

(1)

(2)

(3)

(4)

Содержание MELSEC iQ-R series























































































Результаты поиска

Содержание MELSEC iQ-R series

Отзывы:

Похожие инструкции для MELSEC iQ-R series

Бренды по названию

Популярные бренды

Mitsubishi MELSEC iQ-R series, Руководство пользователя

Результаты поиска

Содержание MELSEC iQ-R series

Отзывы:

Похожие инструкции для MELSEC iQ-R series

Бренды по названию

Популярные бренды