Mitsubishi L2A Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 44

background image

21 / 44

Operation Manual Mitsubishi SL-Series diesel engines
Version 08/2004

OPERATION

ENGLISH

5

OPERATION

5.1

Pre-start inspection

5.1.1 Walk-around Inspection

Look around for items such as loose bolts, debris
build-up, oil, fuel, or coolant leaks, broken or worn
parts.

5.1.2 Check engine oil level

Maintain the engine oil level between the MAX
and MIN marks on the dipstick. Add oil if
necessary (see page 34).

5.1.3 Check fuel level

Make sure that the fuel level is at the FULL mark
in the sight gauge.

5.1.4 Check the coolant level

Maintain the coolant level to the FULL mark on the
reservoir tank (when the engine is cold). Add
coolant when necessary.

NOTE

The engine should be put in the horizontal
position to check the oil level. The dipstick
should be withdrawn, wiped clean, re-inserted in
the oil level guide for 2 seconds, and again
withdrawn so that the oil level on the dipstick can
be seen.

NOTE

When adding coolant, maintain the
recommended concentration of Long Life
Coolant (see page 36). Do not add water. This
dilutes Long Life Coolant and adversely affects
the freeze protection.

CAUTION

Check the coolant level only when the engine is
cold.

«
...
19
20
21
22
23
...
»

Содержание L2A













































Отзывы:

Нет отзывов

Похожие инструкции для L2A

Бренд: GAPOSA Страницы: 20

Бренд: Econex Страницы: 14

Бренд: Nissei Страницы: 16

Бренд: Saito Страницы: 2

Бренд: Newland Страницы: 29

Бренд: Volvo Penta Страницы: 40

Бренд: Volvo Penta Страницы: 48

Бренд: Volvo Penta Страницы: 76

Бренд: Volvo Penta Страницы: 124

Бренд: Volvo Penta Страницы: 140

EASY-KART 100cc

Бренд: IAME Страницы: 35

Бренд: Lycomin Страницы: 171

Бренд: Winterthur Gas Страницы: 495

Бренд: Wren Turbines Страницы: 13

Бренд: Wren Turbines Страницы: 40

Бренд: Detroit Diesel Страницы: 40

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды