background image

FX2N-64CL-M CC-Link/LT Master Block

Program Example 11

11-3

11.1

System Startup Procedure

Start

Install the FX

2N

-64CL-M, remote modules and power adapter / dedicated power supply to the control panel and machine.

Connect the FX

2N

-64CL-M, remote modules and power adapter / dedicated power supply with

cables, and connect terminal resistors at the ends of the trunk line.

Terminating CONFIG mode

Turn OFF the power to the power adapter or dedicated power supply, and then turn OFF the power to the main unit.

Set the DIP switch in the FX

2N

-64CL-M to the ONLINE mode.

Turn ON the power to the power adapter or dedicated power supply, and then turn ON the power to the main unit.

Confirming the operation based upon LEDs
FX

2N

-64CL-M

- Data link is normal: L RUN is lit.
- Data link is abnormal: L ERR. is lit or flickering.
- Setting is abnormal: The ERR. is lit.
Remote module
- Confirm remote station connection by checking buffer memory [BFM #0 (0h) to #3 (3h)] in the
  FX

2N

-64CL-M.

- Confirm device operation using peripheral equipment for the PLC (with regard to monitorly and
  forcing outputs ON and OFF).

Write a control program to the main unit.

Operate the system.

End

Set the transmission speed, point mode, station number, etc. of the FX

2N

-64CL-M and remote

modules using the DIP switches. (Set the FX

2N

-64CL-M to the CONFIG mode.)

Check the following items before turning the power ON.

Confirm the installation status of the FX

2N

-64CL-M, remote modules and power adapter / dedicated power supply.

- Confirm the supply voltage input to the power adapter or dedicated power supply.
- Confirm that the RUN/STOP switch for the main unit is set to STOP.
- Confirm that the same station number is not used in two or more remote modules.

Executing CONFIG mode

Turn ON the power to the power adapter or dedicated power supply, and then turn ON the power to the main unit.

(Specify reserved stations and edit the detailed remote station information here if necessary.)

Refer to
Section 5.

Refer to
Section 6.

Refer to
Sections 1
and 7.

Refer to
Section 8.

Refer to
Sections 10
and 12.

Refer to
Section 11.

Содержание FX2N-64CL-M































































































Отзывы: