background image

Section 1. Operation  

Starting and stopping the engine  
 

Before starting the engine, be sure to check the following 
points. 

1.

 

Confirm that the fuel tank is filled with sufficient fuel. 

2.

 

Check the amount of oil in the engine and transmission. 

3.

 

 Check the coolant water level. 

4.

 

Always perform the daily maintenance described in SECTION 2 

STARTING 

 

On this tractor, the safety starter switch is provided for preventing unforeseen accidents 

form breaking out starting the engine.  Installed between the starter switch and the starter 

motor, the safety starter switch works as a kind of circuit breaker by which, in case the clutch is 

not disengaged completely, the electric circuit in the engine starting system is not closed even 

when the key is turned to the START position. 

1.

 

Set the throttle lever at the center between idling and high speed

 

2.

 

After applying the parking brake, place the main shift lever and PTO shift lever in 
neutral.  Then fully depress the clutch pedal 

3.

 

Insert the starter key into the key switch and turn it counter-clockwise and hold it 
at the “Heat” position to heat the glow plugs.  As soon as the glow plug signal on 
the instrument panel glows red, about 30 seconds latter, rapidly turn the key to 
the “Start” position and the starter motor will rotate and the engine will start 

4.

 

When the engine is started, take your hand off the key and the key then 
automatically returns to the “ON” position.  The key must be in the “On” position 
while the engine is running. 

5.

 

After starting the engine, make sure the battery charge warning lamp, water 
temperature warning lamp and engine oil pressure warning lamp are off.  If any 
one of the lamps will not turn off, or lights up, stop the engine immediately, check 
the cause and then take the necessary countermeasures. 

6.

 

If the engine does not start on the first attempt, do not rotate the starter motor 
continuously more than 10 second.  Then heat the glow plug well and restart the 
engine. 

7.

 

Warm up the engine especially in cold weather, before working. 

Содержание 1540 FD

























Отзывы: