EN-28
11. Press the LENS SHIFT button. The LENS SHIFT menu appears at the center of the screen.
12. Press the
or
button to adjust the vertical position and
or
button to adjust the horizontal position of the
displayed image.
t 8IFOUIFJNBHFJTOPUEJTQMBZFEXJUIJOUIFTDSFFOBEKVTUUIFQSPKFDUJPOBOHMF*OBEEJUJPOQFSGPSNUIF
keystone adjustment, if necessary. (See page 14.)
Repeat steps 4, 5 and 9 to 12, if necessary.
Important:
t 'PDVT[PPNBOEMFOTTIJGUBEKVTUNFOUJTQPTTJCMFJOUIFOPSNBMQJDUVSFNPEFPOMZ
To stop projecting:
13. Press the POWER button.
t "DPOmSNBUJPONFTTBHFJTEJTQMBZFE
t 5PDBODFMUIFQSPDFEVSFMFBWFUIFQSPKFDUPSGPSBXIJMFPSQSFTTBOZCVUUPOFYDFQUUIF108&3CVUUPO
14. Press the POWER button again.
t 5IFMBNQHPFTPVUBOEUIFQSPKFDUPSHPFTJOUPBTUBOECZNPEF*OUIJTTUBOECZNPEFUIF45"564JOEJDBUPS
blinks green.
15. Wait about 2 and a half minutes for the STATUS indicator to be turned off.
t %VSJOHUIJTQFSJPEPGBOEBIBMGNJOVUFTJOUIFTUBOECZNPEFUIFJOUBLFGBOBOEFYIBVTUGBOSPUBUFUPDPPM
the lamp.
t 5IFBJSPVUMFUGBOTSPUBUFGBTUFSBTUIFUFNQFSBUVSFBSPVOEUIFQSPKFDUPSSJTFT
t 5IPVHIUIFGBOTNBLFMPVETPVOETEVSJOHDPPMJOHTVDITZNQUPNJTOPUBNBMGVODUJPO
16. Unplug the power cord from the outlet.
t 5IF108&3JOEJDBUPSXJMMHPPVU
t *GUIFQPXFSDPSETIPVMECFVOQMVHHFEBDDJEFOUBMMZXIJMFFJUIFSUIFBJSJOMFUGBOPSUIFBJSPVUMFUGBOTBSF
operating or the lamp is on, allow the projector to cool down for 10 minutes with the power off. To light the
lamp again, press the POWER button. If the lamp doesn’t light up immediately, press the POWER button a few
minutes later. If it should still fail to light up, replace the lamp.
t $PWFSUIFMFOTXJUIUIFMFOTDBQUPQSPUFDUJUGSPNEVTU
t *GOFDFTTBSZEJTDPOOFDUUIFDBCMFTGSPNUIFDPNQVUFSBGUFSVOQMVHHJOHUIFQPXFSDPSE
Direct Power OFF
You can turn off this projector just by unplugging the power cord without pressing the POWER button.
t %POUTIVUEPXOUIFQSPKFDUPSXIJMFUIF45"564JOEJDBUPSJTCMJOLJOHBGUFSUIFMBNQMJHIUTVQCFDBVTFUIFMBNQT
life may be shortened.
t %POUUVSOUIFQSPKFDUPSCBDLPOSJHIUBGUFSTIVUUJOHJUEPXOCFDBVTFUIFMBNQTMJGFNBZCFTIPSUFOFE 8BJUBCPVU
10 minutes before turning the projector back on.)
t #FGPSFTIVUUJOHEPXOUIFQSPKFDUPSCFTVSFUPDMPTFUIFNFOVTDSFFO*GZPVTIVUEPXOUIFQSPKFDUPSXJUIPVU
closing the menu, the setting data of the menu may not be saved.
t *GZPVTIVUEPXOUIFQSPKFDUPSXIJMFDPOUSPMMJOHUIFQSPKFDUPSVTJOHUIFOFUXPSLGVODUJPOUIFBQQMJDBUJPOTPGUXBSF
such as ProjectorView may fail. The data such as the operating time and temperature display may not be
changed. In such a case, close the browser and then start up again.
t %POUTIVUEPXOUIFQSPKFDUPSXIJMFUIFmMUFSJTSPMMJOH XIJMFUIF'*-5&3JOEJDBUPSJTCSJOLJOHHSFFO
Volume from the speaker
Press the or
-
button to change the volume from the speaker.
The volume control bar will appear on the screen.
VOLUME 15
t 5IFWPMVNFDPOUSPMCBSXJMMEJTBQQFBSBCPVUTFDPOETBGUFSUIF70-6.&CVUUPOJTSFMFBTFE
t 5IF70-6.&CVUUPOTEPOUGVODUJPOXIJMFUIFNFOVTFMFDUJPOCBSPSUIFNFOVJTCFJOHEJTQMBZFE
t 8IFOBIJHIMFWFMBVEJPTJHOBMTVDIBTB%7%BVEJPTJHOBMJTTVQQMJFEUPUIF"6%*0*/UFSNJOBMTUIFPVUQVU
from the speaker may be distorted.
t 8IFOUIFBVEJPDBCMFJTDPOOFDUFEUPUIF"6%*0065UFSNJOBMUIFTQFBLFSPVUQVUJTNVUFE
t 5IFWPMVNFPGUIFBVEJPGSPNUIF"6%*0065UFSNJOBMJTBMTPDIBOHFECZQSFTTJOHUIF70-6.&CVUUPOT
t 5IFWPMVNFPGUIFBVEJPGSPNUIF"6%*0065UFSNJOBMWBSJFTXJUIJOUIFSBOHFCFUXFFOBOE
Setting the aspect ratio
You can change the aspect ratio of the input video signal (or the ratio of width to height of the image). Change the
setting according to the type of the input video signal. (See page 29.)
Viewing video images (continued)
