EN-5
ENGLISH
Warning:
• The lens cap is for protecting the lens. If you leave
the lens cap on the lens with the projector turned
on, it may be deformed because of heat build-
up. Remove the lens cap when you turn on the
projector.
• One of power cords for the U.S., Europe, U.K.,
Australia, and Korea is provided appropriately.
• This projector uses the power plug of three-pin
grounding type. Do not remove the grounding pin
from the power plug. If the power plug doesn’t fi t
your wall outlet, ask an electrician to change the
wall outlet.
• In case that the power cord for the U.S is provided
with this projector, never connect this cord to any
outlet or power supply using other voltages or
frequencies than rated. If you want to use a power
supply using other voltage than rated, prepare an
appropriate power cord separately.
• Use 100-240 V AC 50/60 Hz to prevent fi re or
electric shock.
• Do not place any objects on the power cord or
do not place the projector near heat sources to
prevent damage to the power cord. If the power
cord should be damaged, contact your dealer for
replacement because it may cause fi re or electric
shock.
• Do not modify or alter the power cord. If the power
cord is modifi ed or altered, it may cause fi re or
electric shock.
Caution:
• Do not replace the lamp immediately after using the
projector because the lamp would be extremely hot
and it may cause burns.
• Use of a battery of wrong type may cause
explosion.
• Only Carbon-Zinc or Alkaline-Manganese Dioxide
type batteries should be used.
• Dispose of used batteries according to your local
regulations.
• Batteries may explode if misused. Do not recharge,
disassemble, or dispose of in fi re.
• Be sure to handle the battery according to the
instructions.
• Load the battery with its positive (+) and negative
(-) sides correctly oriented as indicated on the
remote control.
• Keep batteries out of reach of children and pets.
• Remove the battery, if the remote control is not
used for a long time.
• Do not combine a new battery with an old one.
• If the solution of batteries comes in contact with
your skin or clothes, rinse with water. If the solution
comes in contact with your eyes, rinse them with
water and then consult your doctor.
• Placing the projector directly on a carpet impairs
ventilation by the fans, causing damage or failure.
Put a hard board under the projector to facilitate
ventilation.
• Place the projector at least 50 cm (or 20 inch) away
from the wall to prevent the air inlet grille and the air
outlet grilles that emit hot air from being blocked.
• Do not use the projector in the following locations
and manners, which may cause fi re or electric
shock.
• In a dusty or humid place.
• In an oily, smoky, or damp place such as a
kitchen.
• In order to ensure the safety in case of trouble with
the projector, use an electrical outlet having an
earth leakage breaker to supply the power to the
projector. If you do not have such outlet, ask your
dealer to install it.
• Plug in the power cord fi rmly. When unplugging,
hold and pull the power plug, not the power cord.
• Do not plug in or out the power cord with your
hand wet. It may cause electric shock.
• The lamp can’t be lit again for one minute after
turned off for safety purpose. It will take another
one minute for the STATUS indicator to go out. If
you want to turn on the projector again, wait until
the indicator goes out, and then press the POWER
button.
• The air outlet fans rotate faster as the temperature
around the projector rises.
• When the temperature around the projector rises
high, the sign “Temperature!!” blinks red on the
screen. If the temperature stays high, the lamp will
go out automatically.
Important:
• Do not expose the remote control sensor to direct
sunlight or fl uorescent. Keep a distance at least 2
m (6.5 feet) between the remote control sensor and
the fl uorescent light to ensure correct operation
of the remote control. Inverted fl uorescent light, if
located near the projector, may interfere the remote
control.
• Do not apply force to the lens, because the lens
may be damaged.
• Do not cover the lens with the lens cap while the
lamp is on.
Important safeguards (continued)
