Mitsubishi Electric PLA-RP.BA Series, Руководство по эксплуатации

Страница: 7 / 152

7
3. Operation
3.3. Temperature setting
<“Cool”, “Dry”, “Heat” and “Auto”>
F1 F2 F3 F4
Cool
Room
Auto Set temp.
Mode Temp. Fan
Fri
Press the [F2] button to decrease the preset temperature, and press the
[F3] button to increase.
•
Refer to the table on page 6 for the settable temperature range for dif-
ferent operation modes.
• Preset temperature range cannot be set for Fan/Ventilation operation.
• Preset temperature will be displayed either in Centigrade in 0.5- or
1-degree increments, or in Fahrenheit, depending on the indoor unit
model and the display mode setting on the remote controller.
3.4. Fan speed setting
F1 F2 F3 F4
Cool
Room
Auto Set temp.
Mode Temp. Fan
Fri
Press the [F4] button to go through the fan speeds in the following order.
Auto
• The available fan speeds depend on the models of connected indoor
units.
Note:
●
The number of available fan speeds depends on the type of unit
connected.
●
In the following cases, the actual fan speed generated by the unit
will differ from the speed shown the remote controller display.
1. While the display is in “STAND BY” or “DEFROST” states.
2. When the temperature of the heat exchanger is low in the heat-
ing mode.
(e.g. immediately after heating operation starts)
3.
In HEAT mode, when room temperature is higher than the tem-
perature setting.
4. When the unit is in DRY mode.
3.5. Airflow direction setting
3.5.1 Navigating through the Main menu
<Accessing the Main menu>
F1 F2 F3 F4
Main
Main display:
Cursor Page
Main menu
Vane · Louver · Vent. (Lossnay)
High power
Timer
Weekly timer
OU silent mode
<Item selection>
F1 F2 F3 F4
Main
Main display:
Cursor Page
Main menu
Vane · Louver · Vent. (Lossnay)
High power
Timer
Weekly timer
OU silent mode
Cursor
<Navigating through the pages>
F1 F2 F3 F4
Main
Main display:
Cursor Page
Main menu
Vane · Louver · Vent. (Lossnay)
High power
Timer
Weekly timer
OU silent mode
page
<Saving the settings>
F1 F2 F3 F4
OU silent mode
Mon Tue Wed Thu Fri Sat Sun
Start Stop Silent
-
Setting display:
day
<Exiting the Main menu screen>
F1 F2 F3 F4
Cool
Room
Auto Set temp.
Mode Temp. Fan
Fri
<Display of unsupported functions>
F1 F2 F3 F4
Title
Not available
Unsupported function
Return:
Cool
Room
28.5
Auto Set temp.
Mode Temp. Fan
Fri
28.5
Example display
(Centigrade in 0.5-degree increments)
Press the [MENU] button.
The Main menu will appear.
Press [F1] to move the cursor down.
Press [F2] to move the cursor up.
Press [F3] to go to the previous
page.
Press [F4] to go to the next page.
Select the desired item, and press
the [SELECT] button.
The screen to set the selected item
will appear.
Press the [RETURN] button to exit
the Main menu and return to the
Main display.
If no buttons are touched for 10 minutes, the screen will automatically
return to the Main display. Any settings that have not been saved will
be lost.
The message at left will appear if
the user selects a function not sup-
ported by the corresponding indoor
unit model.