background image

 

 9901025-2 

Page 2 of 21 

 

Thermoscreens / Mitsubishi Electric 

 

Heat Pump Warm Air Curtain System 

 
The Heat Pump Warm Air Curtain System consists of :- 

 a Thermoscreens 'PHV Air Curtain' fitted with a PAC-IF010 Mitsubishi Electric Interface 

PCB 

 a Mitsubishi Electric 'Mr Slim Outdoor Unit'  

 a Thermoscreens 'Manual Room Control' for the manual control option by the occupant 

 
Refer to Mitsubishi Electric if the air curtain is to be controlled via a Building Management 
System (BMS) or Centralised Controller. Do not install Manual Room Control and 
BMS/Centralised Control components together, install either one or the other. 
 
A communications link is supplied to the Thermoscreens Heat Pump Air Curtain from the 
Mitsubishi Electric Outdoor Unit. This link provides control of the heat output of the air curtain 
and tells the air curtain when the outdoor unit is in defrost mode so auxiliary electric element 
heaters (if specified) can provide partial heat back-up during the few minutes of defrost. 
 
The Air Curtain requires a permanent 3 phase electrical supply (3L+N+E) from a local 
switched spur to provide power to the defrost cycle electric heating elements, the air curtain 
fans and the Mitsubishi Electric Interface PCB. If the defrost cycle electric elements are not 
required they can be permanently disconnected, see 'Electrical Connections', and a 1 phase 
electrical supply (1L+N+E) used instead. 
 
High and Low Output in this document refers to the heat pump heating capacity of the Air 
Curtain, not to any electrical rating. 

Heat Pump 
Air Curtain

 

Mitsubishi Electric 

Outdoor Unit 

 

Communications Link

 

Permanent mains electrical supply 

(from local switched spur)

 

for 

 

x

 

Fans 

x

 

Mitsubishi Electric Interface PCB 

x

 

Defrost electric heaters (if used) 

Manual Room 

Control

 

Manual On/Off Control and 

Heat Setting Control 

Optional 
BMS Control 
Interface Board

 

Procon 

A32/M

 

Содержание PHV1000DXE HO






















Отзывы: