１ Safety Precautions
２ Making Sure of Components
５ Installation of remote control holder
３ Before installation
４ Installation of wireless receiving unit
・Incomplete installation could cause electric shock, fire, etc.
・After using this manual, be sure to pass it to the customer together with the instruction manual provided with indoor unit. Ask the customer to keep this installation manual and the
instruction manual in a handy place, and to show them to the engineer when the air-conditioner is moved or repaired. Also ask the customer to pass them to any new user.
・Read these "safety Precautions" thoroughly and install securely.
・Precautions are classified using the following symbols depending on the extent and type of danger by erroneous handling.
Make sure that the following components, along with this manual, are
packed in the box.
●Open the intake grill and remove the corner panel where refrigerant pipes are and where local wires are
drawn into.
※The corner panel removed is not needed.
●Remove the thermistor for room temperature fixed by 1 screw and the control box cover fixed by 3
screws,which is possible to hang temporarily.
Remote control holder can be used for keeping the remote controller on the wall.
Fitting remote controller into holder
① Fix the remote control holder to the wall using
the two wood screws provided.
② Insert the remote controller into the holder.
Removing remote control
●Pull out the remote controller.
●Bring the cable of wireless receiving unit through the square hole
underneath the corner panel removed where refrigerant pipes are and
where local wires are drawn into.
●As shown in the figure,pull the cable into the inside of the control box
and connect it to CN90 on the indoor controller board. Then fix the
cable by the clamp, being able to remove the receiving unit afterwards in
case.
●Slide the receiving unit in the
direction as shown and fix it by the
screw which is used for the corner panel removed.
●After the installation completed, set the control box and the thermistor
as they were .
・Incomplete installation could cause electric shock, fire, etc.
・Otherwise, the unit could fall, which could cause injury.
・Shortage in electrical circuit capacity or incomplete construction could cause fire, etc.
・Modification or incorrect repair could cause electric shock, fire, etc. Consult the dealer
from whom you purchased the unit.
・Incomplete installation could cause electric shock, fire, etc.Ask the dealer or a specialist
for installation.
・Tension on wires could disconnect them, or cause heat, fire, etc.
・Doing so could cause fault, electric shock, etc.
・Failure to do so could cause fault, electric shock, etc.
・Failure to do so could cause fault, electric shock, etc.
・Failure to do so could cause fault, fire, etc.
・Usage in a place where there is much oil (including machine oil), steam, sulfide gas,
etc. could greatly degrade its performance or damage components.
・This unit could malfunction when affected by inverter equipment, private electric generator, high-frequency medical instruments, radio communication devices, etc. Also, this unit
could adversely affect medical instruments, communication devices, etc., thus interfering with human medical treatment, or causing disturbance in broadcast pictures or noise.
・If gas leaks or accumulates around the unit, it could cause ignition, explosion, etc.
・Avoid installing in a wall where condensation occurs. Installing in such a place could
cause a fault, electric shock, etc.
・Installing in such a place could cause fault, electric shock, etc.
!
"
#
・Incomplete connection or fixing could cause heat, fire, etc.
$
$
・Installing in such a place could cause deformation, fault, etc.
%&
℃
&
℃
$
CAUTION
WARNING
CAUTION
WARNING
Erroneous handling can cause death or serious injury.
This manual describes the installation for wireless remote controller of the Mitsubishi package air-conditioner.
Read this manual or unit's installation manual carefully.
Mitsubishi Package Air-Conditioner
Installation Manual
Erroneous handling can cause personal injury or damage.
Wireless Remote Controller Kit
PAR-SW96U-E
Component
Wireless Receiving Unit （Corner Panel）
Wireless remote controller
Remote control holder
"AAA" LR03 alkaline batteries
4.1x16 wood screws
1
1
1
2
2
PAR−ＳW96U−E
Note The remote signal will reach the receiver over a distance of approx. 7 m in a straight
line and approx. 45゜
left or right. If the infrared receiver is affected by fluorescent light
(especially, inverter type), it may not be able to receive the signal. Take this into
consideration when installing fluorescent lights or replacing them.
Wireless Receiving Unit
（Corner Panel）
Screw
Indoor Controller
Board CN90
Cable
Cramp
Square hole
ペアNO．
Ｊ41
Ｊ42
Indoor Unit
Grill
Refrigerant pipes
Corner Panel
Screw
Screw
Screw
Indoor
Controller
Board
Jumper Wire
Cont. Box Cover
Intake Grill
Intake Sensor
※Turn off the main power before work.
RG79D052H01
