background image

6

4.2. Space required for installation and servicing

1

. The space when installing with the suspension bolts.

(1) Front View (Fig. 4-6)

  A

 Branch box

  B

 On the side of piping

() Side View (Fig. 4-7, Fig. 4-8)

  C

 For indoor installations

  D

 Ceiling board

  E

 Maintenance hole

*1: Minimum 350 mm is required for 90° bends in refrigerant piping.

*2:   is “Min. 200 mm” <recommendation>.

In the case of less than 

00 mm (for example   is 100 mm), the exchange work 

of Branch box from a maintenance hole becomes difficult (Only exchange work 

of a PCB, linear expansion valve coils and sensors are possible).

In the case of “   450 mm”, prepare a maintenance hole at a PCB side (as it is 

shown in Fig. 4-8), and “Min. 300 mm” is needed as distance  .

In the case of less than 300 mm (for example   is 100 mm), the exchange work 

of Branch box, linear expansion valve coils and sensors from a maintenance 

hole becomes difficult (Only exchange work of a PCB is possible .

(3) Top View (Fig. 4-9)

  G

 Refrigerant piping

2

. The space when installing on the floor. (Fig. 4-10

3

.  The space when installing on a wall. (Fig. 4-11)  

The installation direction is limited when installing on a wall. (Fig. 4-1)

 

When installing the unit on the wall, install the piping connected to the outdoor 
unit facing down.  Other ways are not acceptable.

*3:   is “   600 mm” <recommendation>.

5. Refrigerant piping

*  Always follow the specifications written in the installation manual of the outdoor unit. Exceeding these requirements may cause  reduced performance of the equipment, 

and malfunctions.

(3)

G

Min. 250

Fig. 4-9

(1)

(2)

50

450

450

250

250

250

170

30

278

180-200

A

C

B

D

E

*1

*3

*2

E

D

Fig. 4-6

Fig. 4-7

Fig. 4-8

4. Dimensions and required servicing space of Branch Box

Min. 250

Min. 250

Min. 250

Min. 50

Fig. 4-10

NO

NO

NO

YES

Fig. 4-12

Min. 250

Min. 250

Min. 250

Min. 50

Fig. 4-11

(mm)

(mm)

(mm)

(mm)

(mm)

(mm)

Содержание PAC-MK30BC
















Отзывы: