Mitsubishi Electric MSZ-LN25VGB Скачать руководство пользователя страница 43

Страница: 43 / 48

OPERATING PROCEDURE

PHOTOS

5. Removing the DISPLAY AND i-see SENSOR

ASSEMBLY, the switch buzzer P.C. board, the
display and receiver P.C. board, and the inter-
lock switch (Photo 9)

(1) Disengage the 4 catches of the display cover, and

remove the display cover (Photo 9-1).

(2) Remove the lead wires of the DISPLAY AND i-see

SENSOR ASSEMBLY from the hooks (Photo 9-2).

(3) Disengage the 4 catches of the switch holder, and

remove the switch holder (Photo 9-3).

(4) Turn over the switch holder. Remove the lead wires of

the switch buzzer P.C. board, the display and receiver
P.C. board, and the interlock switch from the hook.
Remove the switch buzzer P.C. board, the display
and receiver P.C. board, and the interlock switch
(Photo 9-4).

Photo 9

(Details of the display, DISPLAY AND i-see SENSOR ASSEMBLY, and board in the switch holder)

Display cover

Exploded view of display cover

and DISPLAY AND i-see SENSOR

ASSEMBLY (Switch buzzer P.C.

board, display and receiver P.C.

board)

Right side view of

DISPLAY AND i-see

SENSOR ASSEMBLY

Front view of DISPLAY AND

i-see SENSOR ASSEMBLY

Display cover

Photo 9-1

Photo 9-4

Photo 9-2

hooks

Top view of DISPLAY AND

i-see SENSOR ASSEMBLY

Switch
holder

Photo 9-3

Catches

DISPLAY AND i-see
SENSOR ASSEMBLY

Switch buzzer P.C.
board

Switch holder

Display and receiver P.C. board

Interlock
switch

OBH766

Содержание MSZ-LN25VGB

















































Результаты поиска

Содержание MSZ-LN25VGB

Отзывы:

Похожие инструкции для MSZ-LN25VGB

Бренды по названию

Популярные бренды

Mitsubishi Electric MSZ-LN25VGB, Руководство по обслуживанию

Результаты поиска

Содержание MSZ-LN25VGB

Отзывы:

Похожие инструкции для MSZ-LN25VGB

Бренды по названию

Популярные бренды