Mitsubishi Electric Mr.Slim PEA-RP100, Руководство по установке

Страница: 21 / 24

21
9. Test run
• If the unit cannot be operated properly after the above test run has been performed, refer to the following table to remove the cause.
Symptom
Cause
Wired remote controller LED 1, 2 (PCB in outdoor unit)
PLEASE WAIT
For about 2 minutes
following power-on
After LED 1, 2 are lighted, LED 2 is turned
off, then only LED 1 is lighted. (Correct
operation)
• For about 2 minutes after power-on, operation of the
remote controller is not possible due to system start-up.
(Correct operation)
PLEASE WAIT → Error code
After about 2
minutes has expired
following power-on
Only LED 1 is lighted.
→
LED 1, 2 blink.
• Connector for the outdoor unit’s protection device is not
connected.
• Reverse or open phase wiring for the outdoor unit’s power
terminal block (L1, L2, L3)
Display messages do not appear
even when operation switch is
turned ON (operation lamp does
not light up).
Only LED 1 is lighted.
→
LED 1, 2 blinks
twice, LED 2 blinks once.
• Incorrect wiring between indoor and outdoor units (incorrect
polarity of S1, S2, S3)
• Remote controller wire short
[Output pattern B] Errors detected by unit other than indoor unit (outdoor unit, etc.)
Wireless remote controller
Symptom Remark
Beeper sounds/OPERATION INDICATOR
lamp flashes (Number of times)
1 Indoor/outdoor unit communication error (Transmitting error) (Outdoor unit)
For details, check the LED
display of the outdoor controller
board.
2 Compressor overcurrent interruption
3 Open/short of outdoor unit thermistors
4 Compressor overcurrent interruption (When compressor locked)
5 Abnormal high discharging temperature/49C worked/ insufficient refrigerant
6 Abnormal high pressure (63H worked)/ Overheating safeguard operation
7 Abnormal temperature of heat sink
8 Outdoor unit fan protection stop
9 Compressor overcurrent interruption/Abnormal of power module
10 Abnormality of super heat due to low discharge temperature
11
Abnormality such as overvoltage or voltage shortage and abnormal
synchronous signal to main circuit/Current sensor error
12 –
13 –
14 Other errors (Refer to the technical manual for the outdoor unit.)
*1 If the beeper does not sound again after the initial two beeps to confirm the self-check start signal was received and the OPERATION INDICATOR lamp does
not come on, there are no error records.
*2 If the beeper sounds three times continuously “beep, beep, beep (0.4 + 0.4 + 0.4 sec.)” after the initial two beeps to confirm the self-check start signal was
received, the specified refrigerant address is incorrect.
• On wireless remote controller
The continuous buzzer sounds from receiving section of indoor unit.
Blink of operation lamp
• On wired remote controller
Check code displayed on the LCD.
• Check that all LEDs on the two control boards on the indoor unit are lit or blinking (3 each, 6 total).
9.3. Test run
9.3.1. Using wireless remote controller (option)
[Fig. 9-3] (P.11)
① Turn on the power to the unit at least 12 hours before the test run.
② Press the TEST RUN button Ⓐ twice continuously.
(Start this operation from the status of remote controller display turned off.)
TEST RUN and current operation mode are displayed.
③ Press the MODE button Ⓑ to activate COOL mode, then check whether cool
air is blown out from the unit.
④ Press the MODE button Ⓑ to activate HEAT mode, then check whether warm
air is blown out from the unit.
⑤ Press the FAN button Ⓒ and check whether fan speed changes.
⑥ Press the VANE button Ⓓ and check whether the auto vane operates properly.
⑦ Press the ON/OFF button to stop the test run.
Note:
• Point the remote controller towards the indoor unit receiver while
following steps ② to ⑦ .
• It is not possible to run the in FAN, DRY or AUTO mode.
[Output pattern A] Errors detected by indoor unit
Wireless remote controller
Wired remote
controller
Symptom Remark
Beeper sounds/OPERATION
INDICATOR lamp flashes
(Number of times)
Check code
1 P1 Intake sensor error
2 P2, P9 Pipe (Liquid or 2-phase pipe) sensor error
3 E6, E7 Indoor/outdoor unit communication error
4 P4 Drain sensor error
5 P5 Drain pump error
6 P6 Freezing/Overheating safeguard operation
7 EE Communication error between indoor and outdoor units
8 P8 Pipe temperature error
9 E4 Remote controller signal receiving error
10 – –
11 PB Fan motor error
12 Fb Indoor unit control system error (memory error, etc.)
No sound – – No corresponding