Mitsubishi Electric MR-J5 Series Скачать руководство пользователя страница 172 | Manualshive

Страница: 172 / 316

background image

170

6 OPTIONS AND PERIPHERAL EQUIPMENT
6.9 Molded-case circuit breakers, fuses, magnetic contactors

For control circuit power supply

When the wiring for the control circuit power supply (L11/L21) is thinner than that for the main circuit power supply (L1/L2/L3),
install an overcurrent protection device (molded-case circuit breaker, fuse, etc.) to protect the branch circuit.

*1 When having the servo amplifier comply with the IEC/EN/UL/CSA standard, refer to "Compliance with global standards" in the following

user's manuals.



MR-J5-G/MR-J5W-G User's Manual (Introduction)



MR-J5-A User's Manual (Introduction)

When using the servo amplifier with the DC power supply input

When using a fuse instead of the molded-case circuit breaker, use the one having the specifications given in this section.

■

For main circuit power supply [G] [A]

*1 Use a molded-case circuit breaker that has operation characteristics equal to or higher than Mitsubishi Electric general-purpose

products.

*2 Use a magnetic contactor with an operation delay time (interval between current being applied to the coil until closure of contacts) of 80

ms or less.

Servo amplifier

Molded-case circuit breaker

Fuse (Class T)

Fuse (Class K5)

Frame, rated
current

Voltage AC [V]

Current [A]

Voltage AC [V]

Current [A]

Voltage AC [V]

MR-J5-10_

30 A frame 5 A

240

1

300

1

250

MR-J5-20_

MR-J5-40_

MR-J5-60_

MR-J5-70_

MR-J5-100_

MR-J5-200_

MR-J5-350_

MR-J5W2-22G

MR-J5W2-44G

MR-J5W2-77G

MR-J5W2-1010G

MR-J5W3-222G

MR-J5W3-444G

Servo
amplifier

Molded-case circuit breaker

Fuse

Magnetic
contactor

Frame, rated current

Voltage AC
[V]

Class

Current [A]

Voltage DC
[V]

Power factor
improving
reactor is not
used

Power factor
improving
reactor is used

MR-J5-10_

30 A frame 5 A

30 A frame 5 A

240

T

10

400

DUD-N30

MR-J5-20_

30 A frame 5 A

30 A frame 5 A

MR-J5-40_

30 A frame 10 A

30 A frame 5 A

15

MR-J5-60_

30 A frame 15 A

30 A frame 10 A

20

MR-J5-70_

30 A frame 15 A

30 A frame 10 A

MR-J5-100_
(3-phase power
supply input)

30 A frame 15 A

30 A frame 10 A

MR-J5-100_
(1-phase power
supply input)

30 A frame 15 A

30 A frame 15 A

30

MR-J5-200_

30 A frame 20 A

30 A frame 20 A

40

MR-J5-350_

30 A frame 30 A

30 A frame 30 A

70

«
...
170
171
172
173
174
...
»

Содержание MR-J5 Series





























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MR-J5 Series

Бренд: Ultrasound Страницы: 6

Бренд: dB Страницы: 6

Бренд: icon Audio Страницы: 4

Бренд: Nady Audio Страницы: 2

Axiom HPD3400PFC

Бренд: PROEL Страницы: 24

HD-AMP1/U1B/K1B/FN

Бренд: Marantz Страницы: 99

Princeton Reverb

Бренд: Fender Страницы: 32

Бренд: Klipsch Страницы: 32

Бренд: VAC Страницы: 11

Бренд: Audio Authority Страницы: 2

Бренд: Radio Shack Страницы: 7

Бренд: t.amp Страницы: 10

Бренд: CableTronix Страницы: 5

Бренд: Amperes Страницы: 8

Blues-junior IV

Бренд: Fender Страницы: 16

Бренд: Clarion Страницы: 3

Бренд: AVPro Edge Страницы: 15

SUPPORT CREW POWER10.1A

Бренд: Bass Face Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды