Mitsubishi Electric MELSOFT FR Configurator2, Инструкция по эксплуатации

Страница: 68 / 230

67
1. OUTLINE
1.5 Setting of operation mode of the inverter
1
2
3
4
5
6
7
8
9
10
○ : Enabled, ×: Disabled, Δ : Some are enabled
*1 As set in Pr.338 Communication operation command source , Pr.339 Communication speed command source .
*2 If an error occurs in the RS-485 communication or Ethernet communication, the inverter cannot be reset from the computer.
*3 Enabled only when stopped by the PU. At a PU stop, PS is displayed on the operation panel. The operation is as set in Pr.75 Reset selection/
disconnected PU detection/PU stop selection .
*4 Some parameters may be write-disabled according to the Pr.77 Parameter write selection setting and operating status.
USB
connector
3 (USB
connector)
9999
(automatic
recognition,
with USB
connection)
Run command
(start, stop)
○ × × ○ ×
Running
frequency
setting
○ × ○ × ×
Monitor ○ ○ ○ ○ ○
Parameter write
○
*4
×
*5
×
*5
×
*5
×
*5
Parameter read ○ ○ ○ ○ ○
Inverter reset ○ ○ ○ ○ ○
Other than
the above
Run command
(start, stop)
× × × × ×
Running
frequency
setting
× × × × ×
Monitor ○ ○ ○ ○ ○
Parameter write ×
*5
×
*5
×
*5
×
*5
×
*5
Parameter read ○ ○ ○ ○ ○
Inverter reset ○ ○ ○ ○ ○
Ethernet
board
5 (Ethernet
board)
Run command
(start, stop)
○ × × ○ ×
Running
frequency
setting
○ × ○ × ×
Monitor ○ ○ ○ ○ ○
Parameter write
○
*4
×
*5
○
*4
○
*4
×
*5
Parameter read ○ ○ ○ ○ ○
Inverter reset ○ ○ ○ ○ ○
Other than
the above or
when the
CC-Link IE
Field
Network
Basic is
selected
Run command
(start, stop)
× × × × ×
○
*1
×
Running
frequency
setting
× × × × ○
○
*1
×
Monitor ○ ○ ○ ○ ○ ○ ○
Parameter write ×
*5
×
*5
×
*5
×
*5
×
*5
○
*4
×
*5
Parameter read ○ ○ ○ ○ ○ ○ ○
Inverter reset × × × × ×
○
*2
×
Communic
ation
option
—
Run command
(start, stop)
× × × × × ×
○
*1
Running
frequency
× × × × × ×
○
*1
monitor ○ ○ ○ ○ ○ ○ ○
Parameter write ×
*5
×
*5
×
*5
×
*5
×
*5
×
*5
○
*4
Parameter read ○ ○ ○ ○ ○ ○ ○
Inverter reset × × × × × ×
○
*2
External
terminal at
the control
circuit
—
Inverter reset ○ ○ ○ ○ ○
Run command
(start, stop)
× ○ ○ ×
×
*1
Running
frequency
setting
× ○ × ×
×
*1
Operation
location
Condition
(Pr. 551
setting) Item
Controllability in each operation mode
PU
operation
External
operation
External/
PU
combined
operation
mode 1
(Pr. 79 = 3)
External/
PU
combined
operation
mode 2
(Pr. 79 = 4)
NET
operation
(when RS-
485
terminals
is used)
*6
NET
operation
(when the
Ethernet
connector
is used)
*7
NET operation
(when a
communication
option is
used)
*8