manualshive.com logo in svg

Mitsubishi Electric MELSEC iQ-F FX55-ASL-M, Руководство пользователя

Поделиться
Скачать
Mitsubishi Electric MELSEC iQ-F FX55-ASL-M Скачать руководство пользователя страница 54

52

7  PARAMETER SETTINGS
7.2  Basic Setting

Transmission points

Set the number of transmission points of AnyWireASLINK.

Startup operating mode

Set whether to read the parameters of slave modules at start-up of the FX5-ASL-M.

Double verification

Set the double verification of the FX5-ASL-M.

*1 The word double verification be selected from until 1st word up to until 15th word.

Error status automatic recovery

Set whether to automatically recover the FX5-ASL-M from the error status.

Item

Description

Setting range

Transmission points setting (IN)

Set the number of input transmission points.
One transmission cycle time is determined by setting the number 
of transmission points. (

Page 85 Transmission cycle time)

• 0 input points
• 8 input points
• 16 input points
• 24 input points
• 32 input points
• 48 input points
• 64 input points
• 80 input points
• 96 input points
• 128 input points
• 160 input points
• 192 input points
• 224 input points
• 256 input points

(Default: 256 input points)

Transmission points setting (OUT)

Set the number of output transmission points.
One transmission cycle time is determined by setting the number 
of transmission points. (

Page 85 Transmission cycle time)

• 0 output points
• 8 output points
• 16 output points
• 24 output points
• 32 output points
• 48 output points
• 64 output points
• 80 output points
• 96 output points
• 128 output points
• 160 output points
• 192 output points
• 224 output points
• 256 output points

(Default: 128 output points)

Item

Description

Setting range

Startup operating mode setting

Set the operation mode at start-up. (

Page 34 Slave 

Information Acquisition at Start-up Function)

• Without slave information acquisition
• Get slave information acquisition

(Default: Without slave information acquisition)

Item

Description

Setting range

Double verification mode setting

Set the double verification mode. (

Page 24 Double 

Verification)

• All points, double verification of bit
• Double verification of word (16 bit), until 1st word

*1

• All points, double verification of word (16 bit)

(Default: All points, double verification of bit)

Item

Description

Setting range

Error status automatic recovery 
mode setting

Set the error status automatic recovery mode. (

Page 34 Error 

Status Automatic Recovery Function)

• No error status automatic recovery
• Error status automatic recovery

(Default: No error status automatic recovery)

Содержание MELSEC iQ-F FX55-ASL-M

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды