Mitsubishi Electric MELIPC MI5000 Series Скачать руководство пользователя страница 20

Страница: 20 / 320

1 DIAGNOSTIC AND MAINTENANCE FUNCTIONS
1.1 Watchdog Timer (WDT) Function

DIAGNOSTIC AND MAINTENANCE
FUNCTIONS

This section explains the diagnostic and maintenance functions of the Windows part.

1.1

Watchdog Timer (WDT) Function

This function detects hardware errors of the Windows part of this product.

Watchdog timer types

The watchdog timers that run on the Windows part are as follows.

The watchdog timers of the Windows part and VxWorks part run independently. For the watchdog timers of
the VxWorks part, refer to the following page.



Page 98 Watchdog Timer (WDT) Function

*1 Time-up errors may be detected from hang-ups of the user application.

Monitoring time setting

This section shows the method for setting a watchdog timer monitoring time.

System watchdog timer

A system watchdog timer can be set in "System WDT Setting" of "WDT(Watchdog Timer) Setting (Windows part)".

Window

[Basic Parameter]



[RAS Setting]



[WDT(Watchdog Timer) Setting (Windows part)]

Displayed items

Function name

Description

Windows part

System watchdog timer

Detects errors (system hang-ups, etc.) in the system programs of the Windows part stemming from
hardware abnormalities.

Item

Description

Setting range

Monitoring time

Set the system watchdog timer monitoring time.

1 to 600 (s) (1 s units)
(Default: 5 s)

Содержание MELIPC MI5000 Series

































































































































































































































































































































Результаты поиска

Содержание MELIPC MI5000 Series

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi Electric MELIPC MI5000 Series, Руководство пользователя

Результаты поиска

Содержание MELIPC MI5000 Series

Отзывы:

Бренды по названию

Популярные бренды