Mitsubishi Electric MelcoREMOTE Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 52

background image

Page 24 of 52

11. Server

Connection

MelcoREMOTE requires a connection to a server in order to upload data logs and download configuration and control
data. This connection is via either GPRS or Ethernet. See the

Configuration and Commissioning

section for more

information on configuring the MelcoREMOTE with the correct connection settings.

11.1. GPRS

An active GPRS enabled SIM card needs to be fitted inside the MelcoREMOTE unit to provide a server connection via
GPRS. In addition the supplied GPRS antenna must be fitted and screwed firmly into the unit.

11.1.1. Fitting/Replacing a SIM Card

Under certain circumstances it may be necessary to fit or change the SIM card in the MelcoREMOTE unit.

To do this, follow the following procedure:

1) Ensure the power to the MelcoREMOTE is switched OFF.

2) Remove the MelcoREMOTE from the DIN rail and use a screwdriver to remove the lid, as shown in the

following diagram.

«
...
22
23
24
25
26
...
»

Содержание MelcoREMOTE





















































Отзывы:

Нет отзывов

Похожие инструкции для MelcoREMOTE

Бренд: salmson Страницы: 12

Бренд: ICP DAS USA Страницы: 4

Бренд: Safeline Страницы: 28

Бренд: Safeline Страницы: 8

Бренд: M&S Systems Страницы: 24

Бренд: BRAVILOR BONAMAT Страницы: 76

Бренд: HIKVISION Страницы: 30

Бренд: Controlsoft Страницы: 12

Stick Up Cam Wired

Бренд: ring Страницы: 9

Бренд: Medion Страницы: 220

Бренд: Aiphone Страницы: 20

Бренд: Telefunken Страницы: 41

Бренд: Commax Страницы: 8

Бренд: Aiphone Страницы: 4

Бренд: ION Страницы: 48

Бренд: DEVI Страницы: 2

Бренд: Aerotech Страницы: 48

Бренд: Keysight Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды