manualshive.com logo in svg

Mitsubishi Electric LU2-4652-B1T, Инструкция по эксплуатации

Поделиться
Скачать
Mitsubishi Electric LU2-4652-B1T Скачать руководство пользователя страница 17

F

 Installing the feed regulator bracket

If it is necessary to dismount and reassemble the 
feed regulator bracket and its related parts, install 
it as follows.
Note:  If the feed regulator bracket is poorly 

positioned, the resultant alternating 
movements may be too short or long causing 
defective machine operation.

( 1 )  Set the gap between special screw Ⓐ located 

on the regulator shaft and the side wall of 
the machine arm to 42.6 mm as illustrated to 
the left. (Use a 42.6 mm spacer between these 
parts. This facilitates the operation.)

( 2 )  With the feed regulator stud held as explained 

in step ( 1 )  above, adjust the feed regulator 
bracket. This adjustment should insure a gap 
of 2.3 mm between the periphery of pin Ⓑ 
located on the feed regulator bracket and the 
top cover installing face located on the arm. 
Tighten screw Ⓒ.

G

 Adjustment of the alternating 

stroke sensing potentiometer

(Please refer to the instruction manual for 
LIMISERVO X GMFY also.)
Note:  In case of maladjustment, the proper sewing 

speed may not be obtained.

( 1 )  Turn off the power switch.
( 2 )  Remove all connectors except OPTION B 

connector.

( 3 )  Remove the top cover in the condition which 

set the alternating stroke adjusting dial for 
scale 2.

( 4 )  Turn on the power switch, and then set the 

operation panel of the control box to the input 
display “V2” at the programming mode E.

( 5 )  Loosen the slotted bolt Ⓓ of the potentiometer 

crank.

 

At this time, be careful not to give any 
bending torque to the potentiometer shaft.

( 6 )  Fix the distance between the feed regulator 

shaft special screw Ⓐ and the inner wall of 
the sewing machine arm 42.6 mm.

 

(It is recommended to use the spacer sized 
42.6 mm for quick fixing.)

( 7 )  Turn the potentiometer shaft so that the 

input display “V2” indicates 280 to 289.

Feed lifting rock 

shaft crank (right)

Feed regulator shaft

Feed regulator bracket

42.6 mm

2.3 mm

Ⓑ

Ⓐ

Ⓒ

Potentiometer

42.6 mm

Ⓓ

Ⓐ

HOW TO USE

( 8 )  Tighten the slotted head bolt Ⓓ of the 

potentiometer crank.

( 9 )  Make sure again that the input display “V2” 

indicates 280 to 289. If the display indicates 
the different number from 280 to 289, adjust 
the potentiometer shaft again.

(10)  Turn off the power switch.
(11)  Put the top cover back in the condition which 

set the alternating stroke adjusting dial for 
scale2.

(12)  Connect all the connectors as before.

— 14  —

Содержание LU2-4652-B1T

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды