Mitsubishi Electric GT15, Руководство по подключению

Страница: 309 / 864

8. ETHERNET CONNECTION
8.4 PLC Side Setting
8 - 23
1
P
R
EP
ARA
T
OR
Y
P
R
OCEDURES
FOR
MONIT
O
R
ING
2
D
E
VICE RA
NGE
T
H
A
T
CAN
B
E
SET
3
ACCESS
RA
N
G
E
F
O
R MONIT
O
R
ING
4
HOW T
O
MONIT
O
R
REDUNT
ANT
SYS
TEM
5
BUS CONNECTION
6
DIR
E
CT
CONNECTION T
O
CPU
7
COMP
UT
E
R
L
INK
CONNE
C
T
ION
8
E
T
HE
RN
E
T
CONN
E
C
T
ION
8.4.1 Connecting to Built-in Ethernet
port CPU (one-to one
connection)
This section describes the settings of the GOT and Built-in
Ethernet port CPU in the following case of system
configuration.
POINT POINT POINT
Built-in Ethernet port CPU
For details of Built-in Ethernet port CPU, refer to the
following manual.
Manuals of MELSEC iQ-R Series
Manuals of MELSEC iQ-F Series

System configuration
For connecting one Built-in Ethernet port CPU to one
GOT, the PLC side settings are not required. Set
[Ethernet] for [Controller Setting] on GT Designer3, and
then connect Built-in Ethernet port CPU to the GOT.
(For MELSEC iQ-R Series)
*1 For the settings when using system devices including a hub
and a transceiver, refer to the following.
8.4.6 Connecting to Built-in Ethernet port CPU
(multiple connection)
*2 These setting items do not exist at the PLC side. However,
the virtual values must be set on the GOT side.
■ [Controller Setting] and [Ethernet] of GT Designer3

[Controller Setting] and [Ethernet] of GT
Designer3
POINT POINT POINT
(1) [Controller Setting] and [Ethernet] of GT
Designer3
For [Controller Setting] and [Ethernet] of GT
Designer3, refer to the following.
8.3.1 Setting communication interface
(Communication settings)
(2) Ethernet setting
When connecting Built-in Ethernet port RCPU to a
GOT, the setting items for the network No. and
station No. do not exist at the PLC side. However,
these virtual values must be set on the GOT side.
Therefore, set the network No. and station No.
Set the network No. that does not exist on the
network system and any station No.
(1) Controller setting
(2) Ethernet setting
*1 Set the same value as that of GOT N/W No.
*2 Set a value different from that of GOT PLC No.
*3 In the case of MELSEC iQ-F series, it is FX5CPU.
*4 In the case of MELSEC iQ-F series, it is 5562 (fixed).
*5 In the case of MELSEC iQ-F series, it is TCP (fixed).
<GOT>
(The settings other than the
following are set to the default)
*1
*2
*2
Network No. : 1
PLC No. : 1
IP address : 192.168.3.1
Port No. : 5001
Communication
format : UDP (fixed)
Network No. : 1 (virtual)
PLC No. : 2 (virtual)
IP address : 192.168.3.39
Port No. : 5006 (fixed)
Communication
format : UDP (fixed)
<Connecting to Built-in Ethernet port CPU>
(The following settings are set to the default)
[Controller Setting] and [Ethernet] of GT
Designer3 ■
Item Set value (Use default value)
GOT NET No. 1
GOT PLC No. 1
GOT IP Address 192.168.3.1
GOT Port No.
(Communication)
5001
GOT Port No.
(Ethernet Download)
5014
Default Gateway 0.0.0.0
Subnet Mask 255.255.255.0
Retry 3times
Startup Time 3sec
Timeout Time 3sec
Delay Time 0ms
Item Set value
Ethernet
setting No.1
Host *
N/W No.
1
*1
PLC No.
2
*2
Type
RCPU
*3
IP address 192.168.3.39
Port No.
5006 (fixed)
*4
Communication
UDP (fixed)
*5