JY997D29501F
Safety Precaution
(Read these precautions before using.)
Before using this product, please read this manual and the relevant manuals
introduced in this manual carefully and pay full attention to safety to handle the
product correctly.
The precautions given in this manual are concerned with this product.
In this manual, the safety precautions are ranked as "WARNING" and
"CAUTION".
Depending on circumstances, procedures indicated by "CAUTION" may also be
linked to serious results.
In any case, it is important to follow the directions for usage.
Indicates that incorrect handling may cause hazardous
conditions, resulting in death or severe injury.
Indicates that incorrect handling may cause hazardous
conditions, resulting in medium or slight personal injury
or physical damage.
MOUNTING PRECAUTIONS
Use the memory loader in the environment that satisfies the general
specifications described in GT10 User's manual. Never use the product in
areas with excessive dust, oily smoke, conductive dusts, corrosive gas (salt
air, Cl
2
, H
2
S, SO
2
or NO
2
), flammable gas, vibration or impacts, or exposed
to high temperature, condensation, or rain and wind. Not doing so can cause
an electric shock, fire, malfunction or product damage or deterioration.
STARTUP/MAINTENANCE
PRECAUTIONS
Do not disassemble or modify the memory loader.
Doing so can cause a failure, malfunction, injury or fire.
Do not touch the conductive and electronic parts of the memory loader
directly. Doing so can cause a memory loader malfunction or failure.
When unplugging the cable connected to the GOT, do not hold and pull the
cable portion. Doing so can cause the memory loader or cable to be
damaged or can cause a malfunction due to a cable connection fault.
Do not bent at a sharp angle or tie the memory loader cables.
Doing so can cause the breaking of the cables.
DISPOSAL PRECAUTIONS
When disposing of the product, handle it as industrial waste.
TRANSPORTATION
PRECAUTIONS
Make sure to transport the memory loader and/or relevant unit(s) in the
manner they will not be exposed to the impact exceeding the impact
resistance described in the general specifications of this manual, as they are
precision devices. Failure to do so may cause the unit to fail.
Compliance with EC directive (CE Marking)
This note does not guarantee that an entire mechanical module produced in
accordance with the contents of this note will comply with the following standards.
Compliance to EMC directive for the entire mechanical module should be checked by
the user / manufacturer. For more details please contact the local Mitsubishi Electric
sales site.
Attention
This product is designed for use in industrial applications.
Authorized Representative in the European Community:
Mitsubishi Electric Europe B.V.
Gothaer Str. 8, 40880 Ratingen, Germany
Requirement for Compliance with EMC directive
The following products have shown compliance through direct testing (to the identified
standards) and design analysis (forming a technical construction file) to the European
Directive for Electromagnetic Compatibility (2004/108/EC) when used as directed by
the appropriate documentation.
Type :Programmable Controller (Open Type Equipment)
For more details please contact the local Mitsubishi Electric sales site.
Associated Manuals
The following manuals are relevant to this product. When these loose manuals are
required, please consult with our local distributor.
Bundled Items
Standard
Remark
EN61131-2 : 2007
Programmable
controllers-
Equipment,
requirement and tests
EMI Compliance with all relevant aspects of the
standard. (Radiated Emissions)
EMS
Compliance with all relevant aspects of the
standard.
(ESD, RF electromagnetic field, EFTB, Surge, RF
conducted disturbances and Power frequency
magnetic field)
Manual name
Contents
Manual
Number
(Model Code)
GT10 User's Manual
Describes the GT10 hardware-relevant
content such as part names, external
dimensions, mounting, power supply
wiring, specifications, and introduction to
option devices.
(sold separately)
JY997D24701
(09R819)
GT Designer2
Version2 Basic
Operation/Data
Transfer Manual
(For GOT1000 Series)
Describes methods of the GT Designer2
installation operation, basic operation for
drawing and transmitting data to
GOT1000 series
(sold separately)
SH-080529ENG
(1D7M24)
GT Designer3
Version1 Screen
Design Manual
(For GOT1000 Series)
(Fundamentals)
Describes methods of the GT Designer3
installation operation, basic operation for
drawing and transmitting data to
GOT1000 series
(sold separately)
SH-080866ENG
(1D7MB9)
Bundled item
Quantity
GT10-LDR memory loader
1
USB cable (1m)
1
GT10-LDR Memory loader USER'S MANUAL (This manual)
1
1. Overview
GT10-LDR memory loader is the memory transfer module that reads/writes the data to GT10 or between a PC (GT Designer2 Ver.2.77F or later, GT Designer3 Ver.1.01B or
later) and GT10-LDR.
*1 When GT10-LDR is connected to a PC via the USB hub, the power supply of the USB hub must be supplied by the AC adopter of the USB hub.
GT10-LDR connected to the USB hub may not work properly depending on the PC environment. In the case, connect the GT10-LDR directly to the USB port on the PC.
2. Specifications
2.1 General Specifications
*1 The wet bulb temperature is 39
C or less.
*2 Do not use or store the GOT under pressure higher than the atmospheric pressure of altitude 0m (0ft.). Failure to observe this instruction may cause a malfunction.
When the air inside the control panel is purged by pressurization, the surface sheet may be lifted by high pressure. As a result, the touch panel may be difficult to press,
and the sheet may be peeled off.
*3 This indicates the section of the power supply to which the equipment is assumed to be connected between the public electrical power distribution network and the
machinery within the premises.
Category II applies to equipment for which electrical power is supplied from fixed facilities.
The surge voltage withstand level for up to the raged voltage of 300 V is 2500 V.
*4 This index indicates the degree to which conductive material is generated in the environment where the equipment is used.
In pollution degree 2, only non-conductive pollution occurs but temporary conductivity may be produced due to condensation.
2.2 Performance Specifications
*1 ROM in which new data can be written without deleting the written data.
Item
Specifications
Operating ambient temperature
0 to 40
C
Storage ambient temperature
-20 to 60
C
Operating ambient humidity
*1
10 to 90% RH, non-condensing
Storage ambient humidity
*1
10 to 90% RH, non-condensing
Vibration resistance
Conforms to JIS
B3502 and
IEC61131-2
Frequency
Acceleration
Half-amplitude
Sweep Count
Under intermittent
vibration
5 to 9Hz
--
3.5mm
10 times each in X, Y
and Z directions
9 to 150Hz
9.8m/s
2
--
Under continuous
vibration
5 to 9Hz
--
1.75mm
9 to 150Hz
4.9m/s
2
--
Shock resistance
Conforms to JIS B3502, IEC 61131-2 (147 m/s
2
, 3 times each in X, Y and Z directions)
Operating atmosphere
Must be free of lamp black, corrosive gas, flammable gas, or excessive amount of electro conductive dust particles and must be no
direct sunlight. (Same as for saving)
Operating altitude
*2
2000 m (6562 ft) max.
Overvoltage category
*3
II or less
Pollution degree
*4
2 or less
Cooling method
Self-cooling
GT1020, GT1030
PC
(GT Designer2 Ver.2.77F or later
GT Designer3 Ver.1.01B or later)
USB connecting
cable (supplied)
*1
Item
Specifications
Memory
User memory
*1
Flash ROM 7.5Mbyte
Life (Number of write
times)
100,000 times
LED
POWER
green
SET/RUN
green/red/orange
ERROR
green/red/orange
Item
Specifications
Switch
RD/WR selection
switch
Paddle switch
Data selection switch
ENT key
Tactile switch
The use of 100 thousand times is due for
replacement.
(operating force 2.55N
0.69N)
Write protection switch
Slide switch
External dimensions
W70(2.75)
H110(4.33)
D21(0.82)[mm](inch)
Weight
0.2kg
2.3 Communication Specifications
2.4 Power Supply Specifications
3. External Dimensions
External Dimensions
Cable length
4. Part Name
Item
Specifications
GOT communication
Conforming to RS232
Transmission speed :115,200bps
Connector shape
: MINI DIN 6Pins (Male)
PC communication
Conforms to USB2.0 (Full speed is supported.)
(Performs the conversion between USB and serial in
GT10-LDR. After serial conversion, transmission
speed is 115.200bps.)
Connector shape
:USB MINI-B 5Pins (Receptacle)
Item
Specifications
Input power supply voltage
DC5V (DC4.75 to 5.25V)
Supplied from the GOT or PC (Supplied from bus
power)
Fuse
-
Power consumption
0.7W (140mA/DC5V) or less
Unit: mm (inch)
Weight: 0.2kg
110 (4.33")
90 (3.54")
70 (2.75")
21 (0.82")
14
(0.55")
Unit: mm (inch)
240 (9.44")
No.
Name
Specifications
1)
POWER LED
LED to show power status
2)
SET/RUN LED
LED to show that the settings are being checked/the transfer is running
3)
ERROR LED
LED to show error status
4)
RD/WR selection switch
Switch to select read/write direction
5)
Data selection switch
Switch to select the data to be transferred
6)
ENT key
Switch to determine the transfer direction and the data to be transferred, and to start the transfer
1)
2)
3)
12) 13)
6)
9)
10)
11)
14)
4)
5)
7)
8)
5. LED lighting specification
*1 An error message appears on the GOT screen. Apply remedies according to the display.
Refer to the "Chapter 12 Troubleshooting" for details on handling errors.
6. Switch operation specification
*1 When the standard monitor OS and communication driver are transferred from the memory loader to the GOT, starting up the GOT with OS installation screen is
required.
7)
Write protection switch
Switch to prevent the memory loader from being written to the data
8)
USB port
Connection port with a PC (with protection cap)
9)
Reference plate (operating instructions)
Described operating instructions of the memory loader
10)
Reference plate (error contents)
Described lighting status of ERROR LED
11)
Transfer cable
Cable to be connected with the GOT
12)
Strap hole
A hole to attach a strap
13)
Part to be labeled
Space to be labeled (created by user)
14)
Rating plate (Nameplate)
--
No.
Name
Specifications
LED Name
Status
Contents
POWER
POWER LED is lit.
Power is supplied.
POWER LED is not lit.
Power is not supplied.
SET/RUN
POWER LED is not lit.
Before starting the transfer.
Orange light
The transfer direction and the data to be transferred are determined.
Green flashing
The transfer is running.
Green light
The transfer is completed.
Red flashing
The transfer is aborted.
ERROR
POWER LED is not lit.
No errors
Green light*
1
Write protection switch ON
Green flashing*
1
The GOT type that is set in the data to be transferred differs from that of the GOT to which the data is transferred.
Red light*
1
The data to be transferred is broken.
The major version of the standard monitor OS is different from that of the project data.
Red flashing*
1
Communication error occurs between the GOT and the memory loader.
Red
Green*
1
Password is set in the project data.
Orange
Green*
1
OS installation screen is not active
Switch Name
Specifications
RD/WR selection
switch
Switch to select read/write direction
RD : The data is read out from the GOT to the memory loader.
WR : The data is written from the memory loader to the GOT.
Data selection switch
Switch to select the data to be transferred
When reading out the data from the GOT to the memory loader
[P OS] : The standard monitor OS, communication driver, project data, and resource data are read out from the GOT to the memory
loader.
[PROJECT] : The project data and resource data are read out from the GOT to the memory loader.
When writing the data from the memory loader to the GOT
[P OS] : The standard monitor OS, font data, communication driver, and project data are written from the memory loader to the GOT.
[PROJECT] : The project data is written from the memory loader to the GOT.
Write protection switch
Switch to prevent the memory loader from being written to the data
ON : The data cannot be written neither from the GOT or a PC (GT Designer2, GT Designer3) to the memory loader.
OFF : The data can be written from the GOT or a PC (GT Designer2, GT Designer3) to the memory loader.
ENT key
Switch to determine the transfer direction and the data to be transferred, and to start the transfer
The transfer starts by pressing the key twice.
The first pressing of the key determines the read/write direction and the data to be transferred.
(After the read/write direction and the data to be transferred are determined, if RD/WR selection switch and Data selection switch are operated,
the operations that have been made will be canceled.)
(The ENT key must be pressed within 30 seconds after the first pressing of the ENT key. Failure to do so cancels the operations that have been
made.)
The second pressing of the key starts the transfer.
GT10-LDR Memory loader
User's Manual
This manual describes the part names, dimensions, mounting, and specifications
of the product. Before use, read this manual and manuals of relevant products
fully to acquire proficiency in handling and operating the product. Make sure to
learn all the product information, safety information, and precautions.
And, store this manual in a safe place so that you can take it out and read it
whenever necessary. Always forward it to the end user.
Registration
The company name and the product name to be described in this manual are the
registered trademarks or trademarks of each company.
Effective April 2015
Specifications are subject to change without notice.
2007 MITSUBISHI ELECTRIC CORPORATION
Manual Number
JY997D29501F
Date
April 2015
