background image

A-3

INSTALLATION INSTRUCTIONS FOR COMPLIANCE WITH UL

Install the FR-ABR brake resistors as follows:

The resistor may be mounted horizontally or vertically, depending on a

suitable surface location.

When the resistor is mounted externally to the enclosure housing the

inverter, install a solid Type 1 enclosure at least 8 times the volume size

of the resistor that incorporates mesh or perforated steel type ventilation

openings at each end of the resistor. Note, the vent openings shall not be

greater than 10 mm diameter.

Secure the enclosure to a non-combustible surface only, such as metal or

concrete.

Mount the resistor inside the Type 1 enclosure and wire it in accordance

with the NEC for North America installations or any other local codes.

Note, when the resistor and inverter are mounted together within a suitable

enclosure, the mesh covering is not required. Please take care that the

Inverter unit / resistor internal enclosure ambient does not exceed 50 deg. C.

Enclosure surface presents a possible burn hazard. After installation, the

following marking in minimum 3 mm (1/8 in.) sized lettering shall be provided

on the enclosure where visible:

CAUTION : HOT SURFACE. TO REDUCE RISK OF BURN - DO NOT TOUCH.

FR-ABR_UL.book  3 ページ  2004年3月16日 火曜日 午後3時55分

Содержание FR-ABR-(H)0.4K















Отзывы: