Mitsubishi Electric FR-A8ND Скачать руководство пользователя страница 101

Страница: 101 / 104

100

APPENDIX

Appendix 2 DeviceNet Error Code List

The following shows the error response format of the Explicit communication.



The bit set by the master is reverted back.

Byte

Bit7

Bit6

Bit5

Bit4

Bit3

Bit2

Bit1

Bit0

XID



MAC ID of the reception side (master)

0x94

Error code

Added error code

Error

code

Added

error
code

Name

Definition

0x08

0xFF

Service not supported

The requested service was not implemented or was not defined for this Object Class/
Instance.

0x09

0xFF

Invalid attribute value

The setting is out of the attribute data range.

0x0C

0xFF

Object state conflict

The object cannot perform the requested service in its current mode/ state.

0x0E

0xFF

Attribute not settable

A request to modify a non-modifiable attribute was received.

0x13

0xFF

Not enough data

The data sent from the master does not reach the specified number of bytes.

0x14

0xFF

Attribute not supported

The attribute is not supported.

0x15

0xFF

Too much data

The data sent from the master exceeds the specified number of bytes.

0x16

0xFF

Object does not exist

The object (instance) does not exist.

0x1F

0xFF

Vender specific error

An FR-A8ND-specific error occurred.

0x1F

0x11

Vender specific error

A value out of the range was written to the parameter.

Содержание FR-A8ND









































































































Результаты поиска

Содержание FR-A8ND

Отзывы:

Похожие инструкции для FR-A8ND

Бренды по названию

Популярные бренды

Mitsubishi Electric FR-A8ND, Инструкция по эксплуатации

Результаты поиска

Содержание FR-A8ND

Отзывы:

Похожие инструкции для FR-A8ND

Бренды по названию

Популярные бренды