Mitsubishi Electric FR-A800, Инструкция по эксплуатации

Страница: 513 / 1042

Parameters (M) Monitor display and monitor output signal
FR-A800 5 - 333
$
Since the voltage and current display on the operation panel (FR-DU08) is shown in four digits, a
monitor value of more than "9999" is displayed as "
⎯
".
%
The setting is available only for standard models.
&
When the output current is less than the specified current level (5% of the rated inverter current),
the output current is monitored as 0 A. Therefore, the monitored value of an output current and
output power may be displayed as "0" when using a much smaller-capacity motor compared to
the inverter or in other instances that cause the output current to fall below the specified value.
+
Can be changed to the pulse display after the electronic gear using Pr. 430 "Pulse monitor
selection" (refer to page 5-172).
'
Available when the plug-in option or control terminal option is connected.
(
Input terminal monitor details ("1" denotes terminal ON, "0" denotes terminal OFF, and "
⎯
" denotes
undetermined value.)
*
Output terminal monitor details ("1" denotes terminal ON, "0" denotes terminal OFF, and "
⎯
"
denotes undetermined value.)
)
Option input terminal monitor 1 details (FR-A8AX input terminal status, "1" denotes terminal ON
and "0" denotes terminal OFF.)
All are OFF when the option is not connected.
3
Option input terminal monitor 2 details (FR-A8AX input terminal status. "1" denotes terminal ON,
"0" denotes terminal OFF, "
⎯
" denotes undetermined value.)
All are OFF when the option is not connected.
-
Option output terminal monitor details (FR-A8AY/A8AR output terminal status. "1" denotes termi-
nal ON, "1" denotes terminal OFF, and "
⎯
" denotes undetermined value.)
All are OFF when the option is not connected.
.
The increment is 1 when Pr. 37 = "1 to 9998" or when Pr. 144 = "2 to 12" or "102 to 112". (Refer to
page 5-324.)
/
The monitored values are retained even if an inverter fault occurs. Resetting will clear the retained
values.
0
Parameter setting is not available for setting the item as the main monitor data on the LCD
operation panel (FR-LU08) or the parameter unit (FRPU07). Use the monitor function of the FR-
LU08 or the FR-PU07 for setting.
1
Negative values are not displayed on the operation panel. The values "-1 to -32767" are displayed
as "65535 to 32769" on the operation panel.
2
Setting of Pr. 1018 "Monitor with sign selection" is required. Besides, displayed without minus sign
on the operation panel. Confirm the rotation direction with the [FWD] or [REV] indicator.
b15 b0
⎯ ⎯ ⎯ ⎯
CS RES
STP
(STOP)
MRS JOG RH RM RL RT AU STR STF
b15 b0
⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯
SO ABC2 ABC1 FU OL IPF SU RUN
b15 b0
X15 X14 X13 X12 X11 X10 X9 X8 X7 X6 X5 X4 X3 X2 X1 X0
b15 b0
⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯
DY
b15 b0
⎯ ⎯ ⎯ ⎯ ⎯ ⎯
RA3 RA2 RA1 Y6 Y5 Y4 Y3 Y2 Y1 Y0