Mitsubishi Electric A800 Plus Series Скачать руководство пользователя страница 105 | Manualshive

Страница: 105 / 242

background image

Parameter setting procedure for tension sensor feedback speed control

104

TENSION SENSOR FEEDBACK SPEED CONTROL

4.4.2

PID gain adjustment

Adjust the PID gain for tension sensor feedback speed control.



Adjustment by tension PI gain tuning (recommended)

The PID gain is adjusted by tension PI gain tuning (refer to

). Tension PI gain tuning is recommended for PID gain

adjustment.



Manual adjustment

• Set the minimum-diameter roll for winding and the maximum-diameter roll for unwinding. Connect the material from the

beginning to the end of the machine, and increase the line speed gradually while observing the tension feedback value.
Adjust the line speed so that appropriate tension feedback value can be obtained.

• Adjust the PID gain so that the dancer roll works without problems at acceleration, constant speed, deceleration, and

sudden deceleration.

• It is important to adjust the tension PI gain as high as possible for the minimum-diameter roll.
• Normally, adjust the gain with

Pr.129 PID proportional band

and

Pr.130 PID integral time

.

POINT

POINT

• Adjust the gain so that overshooting occurs once or so before the tension feedback value returns to the set point.

• Refer to the following according to the tension feedback condition.

NOTE

• Set

Pr.134 PID differential time

only when it is necessary as it causes hunting. However, set a small value in

Pr.134

PID

differential time to cease fluctuation of the tension feedback value by disturbance and such at an early point. (Set 0.01 s at
first and gradually increase the value.)

Status

Adjustment method

When the response is
slow (the tension
feedback value is too low)

• Decrease

Pr.129 PID proportional band

by 10%.

• Decrease

Pr.130 PID integral time

by 0.1 s.

• Repeat the adjustment procedure in the range from the minimum diameter to the maximum diameter so that

the dancer roll moves properly at acceleration, constant speed, deceleration, and sudden deceleration.

When the response is
fast (hunting occurs too
frequently)

• Increase

Pr.129 PID proportional band

by 10%.

• Increase

Pr.130 PID integral time

by 0.1 s.

• Repeat the adjustment procedure in the range from the minimum diameter to the maximum diameter so that

the dancer roll moves properly at acceleration, constant speed, deceleration, and sudden deceleration.

Slow response

(the tension feedback position is too low)

Fast response

(hunting occurs too frequently)

Proper condition

«
...
103
104
105
106
107
...
»

Содержание A800 Plus Series



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для A800 Plus Series

SOLECTRIA XGI 1500 Series

Бренд: YASKAWA Страницы: 70

U1000 iQpump Drive

Бренд: YASKAWA Страницы: 118

VARISPEED-616G5

Бренд: YASKAWA Страницы: 355

Бренд: Fagor Страницы: 12

Бренд: Sonoro Страницы: 148

Бренд: VOLTCRAFT Страницы: 10

Maestro Pro 01925

Бренд: Olimpia splendid Страницы: 60

Бренд: April Music Страницы: 11

AK ERP 10 Series

Бренд: HEIDENHAIN Страницы: 20

Бренд: Black Box Страницы: 60

Бренд: Gorman-Redlich Страницы: 3

MAXX SST VEC049GM

Бренд: Vector Страницы: 10

Бренд: Hoymiles Страницы: 29

COM-K IMR01Z01-E9

Бренд: RKC INSTRUMENT Страницы: 2

BLANKOM SDE-1265

Бренд: Irenis Страницы: 22

Teranex Mini IP Video 12G

Бренд: Blackmagicdesign Страницы: 22

Бренд: foxunhd Страницы: 5

Бренд: tams elektronik Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды