Mitel MiVoice Business 3300 ICP Скачать руководство пользователя страница 252

Страница: 252 / 366

Voice Networking

Voice Mail Type

Symptom

Possible Cause

Corrective Action

Users

indicate

that they

are missing

messages.

Messages are in

mailboxes on both

the primary and

secondary ICPs.

Instruct user to check

voice mail messages

in both of their voice

mail boxes (user must

dial different hunt group

numbers to access

the voice mail systems

on the primary and

secondary ICPs).

A voice mail box has

not been configured

on the external

centralized voice

mail controller for the

resilient device.

Configure a voice

mailbox for the user.

Call routing on the

secondary controller

is not configured

to allow a user to

access the voice

mail ports (by dialing

the hunt group

number).

Ensure that call routing is

set up to allow the user

to access the hunt group

number of the voice mail

port. Refer to the

MiVoice

Business Resiliency

Guidelines

for call routing

configuration.

Centralized external

After an IP

phone fails

over to the

secondary

ICP, user

cannot

connect to

the voice

mailbox.

The centralized

voice mail

application or server

is out of service.

Check the voice mail

application and server.

8.5.3 T1 E1 Trunk Resiliency

Document Version 1.0
Troubleshooting Guide

246

Содержание MiVoice Business 3300 ICP















































































































































































































































































































































































Результаты поиска

Содержание MiVoice Business 3300 ICP

Отзывы:

Похожие инструкции для MiVoice Business 3300 ICP

Бренды по названию

Популярные бренды

Mitel MiVoice Business 3300 ICP, Руководство по устранению неисправностей

Результаты поиска

Содержание MiVoice Business 3300 ICP

Отзывы:

Похожие инструкции для MiVoice Business 3300 ICP

Бренды по названию

Популярные бренды