manualshive.com logo in svg

Mitel Inter-Tel Axxess, Руководство администратора, Страница: 134 / 384

Поделиться
Скачать
Mitel Inter-Tel Axxess Скачать руководство пользователя страница 134

Page  118

System Features

Inter-Tel

® 

Axxess

® 

Administrator Guide — Issue 11.0, May 2008

Station Feature Codes

Station Feature Codes

The following pages list the general feature codes. When a default feature button can be used
in place of the feature code, it is indicated at the end of the explanation. Refer to 

page 86

 for a

listing of the default endpoint feature buttons.

Table 17. 

Station Feature Codes 

FEATURE NAME 

CODE 

DEFINITION 

Account Code – All Calls Follow-
ing

391

Allows the station user to enter a forced or optional account code 
that will apply to all calls following the entry of this feature code 
and will appear in the SMDR. To disable the All Calls Following 
feature, the feature code is entered again without an account code.

Account Code – Optional

390

Allows the station user to enter an optional account code for 
SMDR reports during an outside call.

ACD Agent Login
ACD Agent Logout
ACD Agent Login/Logout Toggle

326
327
328

These feature codes allow an ACD hunt group member (agent) to 
log into and out of the ACD hunt group(s). The agent will only 
receive calls through the ACD hunt group(s) while logged in.

ACD Agent Wrap-Up Terminate

329

When an ACD agent completes a call, no other ACD hunt group 
call will ring at the station until the ACD Wrap-Up Timer expires or 
the agent enters this feature code to terminate the wrap-up ses-
sion.

Agent Help

375

The Agent Help feature allows a station user to request help from 
a designated “Agent Help Extension” during a two- or three-party 
call.

Agent Help Reject

376

When a request-for-help call rings, the Agent Help Extension can 
choose to join the call or enter this feature code to reject the 
request.

Answer (Ringing Call)

351

Answers the call that has been ringing or holding the longest at 
that station. Refer to 

page 157

 for the priority list. (Inter-Tel end-

points use the ANSWER button.)

Audio Diagnostics

320

When initiated, users are prompted to answer questions about the 
audio problems by pressing specific dialpad buttons.

Automatic CO Access On/Off

360

(Inter-Tel endpoints Only) 

Allows the endpoint user to determine 

how ringing outside calls will be answered: simply by lifting the 
handset or pressing the Speaker button (automatic answer), or by 
lifting the handset or pressing the Speaker button and pressing a 
Call button, individual trunk button or the ANSWER button.

Automatic IC Access On/Off

361

(Inter-Tel endpoints Only) 

Allows the endpoint user to determine 

how ringing intercom calls will be answered: simply by lifting the 
handset (automatic answer), or by lifting the handset and pressing 
the IC button (or a Call button, if there is no IC button).

Automatic Trunk Answer

350

Using this feature code, station users with allowed answer can pick 
up trunks that are ringing into the system, but that are not actually 
ringing at their stations. This feature does not pick up transferred 
calls or recalls that are ringing at the station.

Содержание Inter-Tel Axxess

































































































































































































































































































































































































Отзывы:

Нет отзывов